DOWNLOAD Manual FireStingO2 (PDF, 4 MB) - Pyro-science.com

More documents

Recommendations

Info

(P) to the oxygen meter FireStingO2. On each sensor, a label (L)with a specific Sensor Code is attached to the fiber-optic cable.The protective plastic tube (PT) covering the bare fiber has to beremoved carefully before using the sensor. For this, fix the plastictube in a stable laboratory stand, loosen the clamping screw andcarefully pull out the bare fiber sensor.NOTE: After removal of the protective plastic tube the fragilesensor tip is unprotected and sensitive to breakage!CAUTION during handling to avoid breakage or injuries!The bare fiber sensorsare available both asmicrosensors (OXB50;A) and as minisensors(OXB230, B; OXB430,C). They can be usedwith customizedhousings withcomplex geometriesor they might beinserted directly into samples ("implantable sensors").18
5.3 Robust ProbesThe Robust Oxygen Probes arecomposed of a black fiber and astainless steel tubing 3 mm indiameter, and 30 or 100 mm inlength (e.g. item no. OXROB3,OXROB10). The oxygensensitive part is the disc 3mm indiameter located at the very end of the tubing (green disc in imagebelow).The Robust Oxygen Probes can be optionally obtained with anoptical isolation (black coating) on the sensing surface (item no.OXROB3-OI, OXROB10-OI), which is recommended forapplications with strong external illumination like direct sun light.The Robust Oxygen Probes can be used for long-termmeasurements in gases and liquids. The whole sensor including itscabling is completely submersible in water and specified forlongtime submersion in liquid media.In contrast to the needle-type sensors, the sensitive sensor tip ofthe robust probe is protected by the steel tubing and is morerobust for standard laboratory applications. Due to thesignificantly bigger dimensions of the robust probes compared toour micro- and minisensors, diffusion limitation in liquid samples of19
Page 2 and 3: Document Version 3.07Refers to Pyro
Page 4 and 5: 7.1.6 Calibration Mode: Custom Mode
Page 6 and 7: 1 OverviewThe compact USB-powered f
Page 8 and 9: 2 Safety GuidelinesThe FireStingO2
Page 10 and 11: Before using the FireStingO2 and it
Page 12 and 13: The FireStingO2 comes with 1, 2, or
Page 14 and 15: 5 Oxygen Sensor TypesFor an overvie
Page 16 and 17: position 0 (retracted position) of
Page 20 and 21: oxygen towards the 3 mm tip has a m
Page 22 and 23: It is important to fix or glue the
Page 24 and 25: 5.7 Connecting the SensorsThe fiber
Page 26 and 27: The bare fiber sensors need to be s
Page 28 and 29: Note that placing the mouse on many
Page 30 and 31: The unit of the x-axis can be chang
Page 32 and 33: Signal too high There might be too
Page 34 and 35: continuous sampling (default settin
Page 36 and 37: In the settings the user has to def
Page 38 and 39: 6.2.2 Advanced SettingsIf Advanced
Page 40 and 41: of the respective oxygen sensor rea
Page 42 and 43: After activation of a temperature s
Page 44 and 45: The activation of the Analog In but
Page 46 and 47: 6.4 Raw Data WindowThe Raw Data Win
Page 48 and 49: 7 Calibration with “Pyro Oxygen L
Page 50 and 51: calibration in air saturated water
Page 52 and 53: If the Sensor code is correct, the
Page 54 and 55: NOTE: If using retractable needle-t
Page 56 and 57: NOTE: If using retractable needle-t
Page 58 and 59: Note that the button Set 0% will be
Page 60 and 61: (°C). Note that the button Set Air
Page 62 and 63: And for the 0% calibration the foll
Page 64 and 65: Consequently, the 0% calibration sh
Page 66 and 67: 7.2.1 Calibration Mode: Factory (1.
Page 68 and 69:
due to the actual weather condition
Page 70 and 71:
Wait for steady state until the sen
Page 72 and 73:
7.3 Advanced adjustmentsThis sectio
Page 74 and 75:
8 Calibration Standards8.1 The Air
Page 76 and 77:
elevation the typical atmospheric p
Page 78 and 79:
8.2 The 0% StandardThe 0% calibrati
Page 80 and 81:
9 Calibration of Contactless Sensor
Page 82 and 83:
one end of the Optical Fiber is con
Page 84 and 85:
10.3 Automatic Temperature Compensa
Page 86 and 87:
11 Analog Output and Auto-ModeThe s
Page 88 and 89:
voltage signals proportional to the
Page 90 and 91:
Here the Auto-Mode Sample Interval
Page 92 and 93:
trigger signal was detected at the
Page 94 and 95:
External Temperature Sensors*Range,
Page 96 and 97:
Pin Name Function Description1 GND
Page 98 and 99:
Auto-Mode with External Power Suppl
Page 100 and 101:
12.2.2 Connector X2 (Analog Output)
Page 102 and 103:
12.4 Measuring PrincipleThe new RED
Page 104 and 105:
12.5 Operating several FireStingO2
Page 106 and 107:
with p100 O2 = 0.2095 ( p atm - p H
Page 108 and 109:
Sal(PSU)Temp0(°C)5 10 15 20 25 30
Page 110:
LED IntensityA 10% E 40%B 15% F 60%
show all

DOWNLOAD Manual FireStingO2 (PDF, 4 MB) - Pyro-science.com

Create successful ePaper yourself

Delete template?

Save as template?