DOWNLOAD Manual FireStingO2 (PDF, 4 MB) - Pyro-science.com

More documents

Recommendations

Info

The activation of the Analog In button allows to read in a voltagesignal at the extension port, e.g. from third-party sensors like a pHsensor. The measuring range is 0-2.5V and the display and outputof the signal is in mV. For details refer to chapter 11.The maximum number of data points kept in the graphs can bechanged by the selector Max. Data Points in Graphs (default:10800). A change of the number will clear the graphs and highvalues (>>10000) might decrease the maximum sample rate.The <strong>FireStingO2</strong> offers four analog outputs (0-2.5V) at theextension port which can be configured by pressing the AnalogOutput button. For details refer to chapter 11.Advanced Options (only for advanced users)!The USB <strong>com</strong>munication speed can be adjusted e.g. for improvingthe maximum sampling rate (default: 57600).Activation of the button Enable High-Speed Sampling will enablethe adjustment of a Sample Interval
6.3 Overview PanelThe sensor readings of all activated oxygen sensors (left y-axis),external and internal temperature sensors, internal pressure andhumidity sensors (right y-axis) and signals from the Analog In (lefty-axis) are displayed in the panel Overview.Each sensor reading is shown also as a numerical value in thechosen unit on top of the overview graph. The plot style of eachchannel in the chart can be changed by clicking on the colorcontrol:By clicking on the small rectangular button of the color control, it ispossible to show or hide the respective graph. This show/hidefunctionality is especially useful, if e.g. a single graph should beinspected in detail while all other graphs are hidden.With Common Plots, Color, Line Style and Width, Interpolationand Point Style each plot in the chart can be changed. The itemsBar Plots, Fill BaseLine, and Y-Scale are not appropriate for thisapplication.45
Page 2 and 3: Document Version 3.07Refers to Pyro
Page 4 and 5: 7.1.6 Calibration Mode: Custom Mode
Page 6 and 7: 1 OverviewThe compact USB-powered f
Page 8 and 9: 2 Safety GuidelinesThe FireStingO2
Page 10 and 11: Before using the FireStingO2 and it
Page 12 and 13: The FireStingO2 comes with 1, 2, or
Page 14 and 15: 5 Oxygen Sensor TypesFor an overvie
Page 16 and 17: position 0 (retracted position) of
Page 18 and 19: (P) to the oxygen meter FireStingO2
Page 20 and 21: oxygen towards the 3 mm tip has a m
Page 22 and 23: It is important to fix or glue the
Page 24 and 25: 5.7 Connecting the SensorsThe fiber
Page 26 and 27: The bare fiber sensors need to be s
Page 28 and 29: Note that placing the mouse on many
Page 30 and 31: The unit of the x-axis can be chang
Page 32 and 33: Signal too high There might be too
Page 34 and 35: continuous sampling (default settin
Page 36 and 37: In the settings the user has to def
Page 38 and 39: 6.2.2 Advanced SettingsIf Advanced
Page 40 and 41: of the respective oxygen sensor rea
Page 42 and 43: After activation of a temperature s
Page 46 and 47: 6.4 Raw Data WindowThe Raw Data Win
Page 48 and 49: 7 Calibration with “Pyro Oxygen L
Page 50 and 51: calibration in air saturated water
Page 52 and 53: If the Sensor code is correct, the
Page 54 and 55: NOTE: If using retractable needle-t
Page 56 and 57: NOTE: If using retractable needle-t
Page 58 and 59: Note that the button Set 0% will be
Page 60 and 61: (°C). Note that the button Set Air
Page 62 and 63: And for the 0% calibration the foll
Page 64 and 65: Consequently, the 0% calibration sh
Page 66 and 67: 7.2.1 Calibration Mode: Factory (1.
Page 68 and 69: due to the actual weather condition
Page 70 and 71: Wait for steady state until the sen
Page 72 and 73: 7.3 Advanced adjustmentsThis sectio
Page 74 and 75: 8 Calibration Standards8.1 The Air
Page 76 and 77: elevation the typical atmospheric p
Page 78 and 79: 8.2 The 0% StandardThe 0% calibrati
Page 80 and 81: 9 Calibration of Contactless Sensor
Page 82 and 83: one end of the Optical Fiber is con
Page 84 and 85: 10.3 Automatic Temperature Compensa
Page 86 and 87: 11 Analog Output and Auto-ModeThe s
Page 88 and 89: voltage signals proportional to the
Page 90 and 91: Here the Auto-Mode Sample Interval
Page 92 and 93: trigger signal was detected at the
Page 94 and 95:
External Temperature Sensors*Range,
Page 96 and 97:
Pin Name Function Description1 GND
Page 98 and 99:
Auto-Mode with External Power Suppl
Page 100 and 101:
12.2.2 Connector X2 (Analog Output)
Page 102 and 103:
12.4 Measuring PrincipleThe new RED
Page 104 and 105:
12.5 Operating several FireStingO2
Page 106 and 107:
with p100 O2 = 0.2095 ( p atm - p H
Page 108 and 109:
Sal(PSU)Temp0(°C)5 10 15 20 25 30
Page 110:
LED IntensityA 10% E 40%B 15% F 60%
show all

DOWNLOAD Manual FireStingO2 (PDF, 4 MB) - Pyro-science.com

Create successful ePaper yourself

Delete template?

Save as template?