DOWNLOAD Manual FireStingO2 (PDF, 4 MB) - Pyro-science.com

More documents

Recommendations

Info

calibration in air saturated water or water-vapor saturated air forprecise measurements around 100% air saturation.2-Point in Ambient Air: taking the 0% and the air calibration valuefrom a manual calibration for precise measurements over the fullrange (0-21% O2). This mode uses the ambient air for determiningthe air calibration value.2-Point in Water or Humid Air: taking the 0% and the aircalibration value from a manual calibration for precisemeasurements over the full range (0-100% dissolved O2 (DO)).This mode uses air saturated water or water-vapor saturated air fordetermining the air calibration value.NOTE: It is re<strong>com</strong>mended to determine the air calibration value inair saturated water if the measurements will be performed in watersamples (aqueous liquids).During the calibration of a sensor connected to a specific channel,the Sample Interval is automatically set to 0.5 s and the DataSmoothing to 5, ensuring a fast determination of a precise meanvalue during the sensor calibration. After finalization of thecalibration, the program returns automatically to the formersettings.For advanced users and applications, a Custom Mode can beselected, allowing the user to <strong>com</strong>bine freely the possiblecalibration types for the air and the 0% calibration.Possible Air Calibration Types in the Custom Mode:Air with 100% Humidity or Air Saturated Water,Ambient Air,Custom Calibration (allowing also calibrations at freelychosen oxygen levels)Factory Air Calibration.50
Possible 0% Calibration Types in the Custom Mode:a manual 0% Calibrationa Factory 0% Calibration.In the following the different calibration modes are described.7.1.1 Calibration Mode: FactoryNOTE: The Factory Calibration is intended only for roughmeasurements and testing purposes. It is only possible if thecorrect Sensor Code has been entered in the Settings (see chapter6.2).If the calibration mode Factory Calibration is chosen, ensure thatthe correct sensor code has been entered in the Settings of thecorresponding channel (as displayed in 2. Adjust CalibrationConditions of the Oxygen Sensor Calibration window). If thesensor code displayed is not correct, click on Finish, go to theSettings, enter the correct Sensor Code and repeat the FactoryCalibration.51
Page 2 and 3: Document Version 3.07Refers to Pyro
Page 4 and 5: 7.1.6 Calibration Mode: Custom Mode
Page 6 and 7: 1 OverviewThe compact USB-powered f
Page 8 and 9: 2 Safety GuidelinesThe FireStingO2
Page 10 and 11: Before using the FireStingO2 and it
Page 12 and 13: The FireStingO2 comes with 1, 2, or
Page 14 and 15: 5 Oxygen Sensor TypesFor an overvie
Page 16 and 17: position 0 (retracted position) of
Page 18 and 19: (P) to the oxygen meter FireStingO2
Page 20 and 21: oxygen towards the 3 mm tip has a m
Page 22 and 23: It is important to fix or glue the
Page 24 and 25: 5.7 Connecting the SensorsThe fiber
Page 26 and 27: The bare fiber sensors need to be s
Page 28 and 29: Note that placing the mouse on many
Page 30 and 31: The unit of the x-axis can be chang
Page 32 and 33: Signal too high There might be too
Page 34 and 35: continuous sampling (default settin
Page 36 and 37: In the settings the user has to def
Page 38 and 39: 6.2.2 Advanced SettingsIf Advanced
Page 40 and 41: of the respective oxygen sensor rea
Page 42 and 43: After activation of a temperature s
Page 44 and 45: The activation of the Analog In but
Page 46 and 47: 6.4 Raw Data WindowThe Raw Data Win
Page 48 and 49: 7 Calibration with “Pyro Oxygen L
Page 52 and 53: If the Sensor code is correct, the
Page 54 and 55: NOTE: If using retractable needle-t
Page 56 and 57: NOTE: If using retractable needle-t
Page 58 and 59: Note that the button Set 0% will be
Page 60 and 61: (°C). Note that the button Set Air
Page 62 and 63: And for the 0% calibration the foll
Page 64 and 65: Consequently, the 0% calibration sh
Page 66 and 67: 7.2.1 Calibration Mode: Factory (1.
Page 68 and 69: due to the actual weather condition
Page 70 and 71: Wait for steady state until the sen
Page 72 and 73: 7.3 Advanced adjustmentsThis sectio
Page 74 and 75: 8 Calibration Standards8.1 The Air
Page 76 and 77: elevation the typical atmospheric p
Page 78 and 79: 8.2 The 0% StandardThe 0% calibrati
Page 80 and 81: 9 Calibration of Contactless Sensor
Page 82 and 83: one end of the Optical Fiber is con
Page 84 and 85: 10.3 Automatic Temperature Compensa
Page 86 and 87: 11 Analog Output and Auto-ModeThe s
Page 88 and 89: voltage signals proportional to the
Page 90 and 91: Here the Auto-Mode Sample Interval
Page 92 and 93: trigger signal was detected at the
Page 94 and 95: External Temperature Sensors*Range,
Page 96 and 97: Pin Name Function Description1 GND
Page 98 and 99: Auto-Mode with External Power Suppl
Page 100 and 101:
12.2.2 Connector X2 (Analog Output)
Page 102 and 103:
12.4 Measuring PrincipleThe new RED
Page 104 and 105:
12.5 Operating several FireStingO2
Page 106 and 107:
with p100 O2 = 0.2095 ( p atm - p H
Page 108 and 109:
Sal(PSU)Temp0(°C)5 10 15 20 25 30
Page 110:
LED IntensityA 10% E 40%B 15% F 60%
show all

DOWNLOAD Manual FireStingO2 (PDF, 4 MB) - Pyro-science.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?