Manual - LP2824 - logmaster

More documents

Recommendations

Info

Printer OperationProblemMedia does notadvance.Media moves butnothing is printed.Printing is faded orpoor.Prints only partiallabel or skips a label.Printing stops andindicator lights Amberor Red.Solution or Reason1. Check interface cable connections from computer toprinter.2. Make sure top cover is locked closed.3. Check that labels are correct.4. Verify media has print surface up for printing.5. Printer has a syntax or command error. Check programand resend print job.1. Verify that the labels are the correct type (direct thermal).2. Check that the roll is loaded with the thermal side facingup.3. Clean the print head with cleaning pen.4. Ensure top cover is locked closed.1. Clean the print head with cleaning pen.2. Adjust print speed/darkness in software.3. Check the media and verify that print surface is facing up.4. Check that correct thermal media is in use.1. Perform media length sensing.2. Label caught on print head.3. Top cover is not properly latched.4. Possible software problem. Check the printer memoryconfiguration. Refer to the programming manual.1. Perform media length sensing.2. Possible problem with label stock. Use only approvedlabels and tags.3. Possible label jam.4. Insufficient memory for label size. Check the printermemory configuration.5. Possible software problem. Refer to the programmingmanual.34 980481-001A
Media HandlingProblemPrinting continuesbetween labels.Prints one label andthen stops.Blade cuts throughlabels instead ofcutting liner betweenlabels.Media jammed incutter.Blade fails to cutdirect thermal paperor label liner.Label DispenserSolution or Reason1. Make sure label-taken sensor is on.2. The label-taken sensor is blocked or dirty. Remove anyscraps or dust.3. Continuous media may be set. Verify form length settingthrough programming Q command. See the programmingguide.1. Verify the quantity has been correctly set.Cutter Operation1. Verify form length setting through programming1. Unplug power and interface cables. Use tweezers toremove scaps from cutter opening.1. Use programming C command to cycle cutter several timeswithout media to perform a self-cleaning. See theprogramming guide.2. Cutter must be replaced.980481-001A 35
Page 1 and 2: Zebra ®LP 2824Desktop PrinterUser
Page 3 and 4: Proprietary StatementThis manual co
Page 5 and 6: ContentsIntroductionHello!. . . . .
Page 7 and 8: 980481-001A vii
Page 9 and 10: IntroductionThis section describes
Page 11 and 12: Inspecting the PrinterLook at the o
Page 13 and 14: Closing the printerLower the top co
Page 15 and 16: Getting StartedThis section describ
Page 17 and 18: Loading Roll MediaWhen you load med
Page 19 and 20: Using the GuidesThe guides direct t
Page 21 and 22: Media Length SensingMOVIEBefore you
Page 23 and 24: USB Interface RequirementsUniversal
Page 25 and 26: Serial CommunicationsSerial communi
Page 27 and 28: Operation & OptionsThis section hel
Page 29 and 30: Printing in Peel-ModeThe optional d
Page 31 and 32: Using the Cutter OptionPrinters tha
Page 33 and 34: MaintenanceCleaningWhen you clean t
Page 35 and 36: Platen ConsiderationsThe standard p
Page 37 and 38: Replacing the Print HeadIn the even
Page 39 and 40: Replacing the LP Print Head (Contin
Page 41: TroubleshootingWhat the Status Ligh
Page 45 and 46: The printing does not start at the
Page 47 and 48: Resetting the Factory Default Value
Page 49 and 50: AppendixInterfacesUniversal Serial
Page 51 and 52: ZebraNet® PrintServer II for Ether
Page 53 and 54: Serial (RJ-11) Alternative Connecto

Manual - LP2824 - logmaster

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?