Manual - LP2824 - logmaster

More documents

Recommendations

Info

Manual CalibrationManual calibration is recommended whenever you are using pre-printedmedia or if the printer will not correctly auto calibrate.1. Make sure the printer power is off and that media is loaded.2. Press and hold the feed button then turn on the printer power.3. Continue to hold the feed button until the status light LED flashes.Release the feed button.4. The printer will set the media sensor for the label backing being used.After the printer is done making this adjustment, the roll willautomatically feed until a label is positioned at the print head.5. The configuration settings (similar to the example below) will print.Upon completion, the printer will save the new settings in memory andremain in diagnostic dump mode.6. Press the feed button. The printer will dispense another label with themessage "Out of DUMP" and be ready for normal operation.UKQ2933H U V4.28.19Serial port : 96,N,8,1Image buffer size: 1032KFmem:000,0K,060.9K avlGmem:000K,0331K avlEmem:000K,0331K avlI8,0,001 rY JF WYS2 D07 R0 24,000 ZT UNq1200 Q 1500,036Option:oRO06 10 16now in DUMPout of DUMP38 980481-001A
Resetting the Factory Default ValuesSometimes, resetting the printer to the factory defaults solves some of theproblems. For troublehooting and to overwrite all stored parameters, sendthe ^default command.Communications DiagnosticsIf there is a problem transferring data between the computer and printer, tryputting the printer in the communications diagnostics mode. The printerwill print the ASCII characters and their respective hexadecimal values (asample is shown below) for any data received from the host computer. Tofind out how, refer to the power off mode procedure in “ManualCalibration” on page 38.980481-001A 39
Page 1 and 2: Zebra ®LP 2824Desktop PrinterUser
Page 3 and 4: Proprietary StatementThis manual co
Page 5 and 6: ContentsIntroductionHello!. . . . .
Page 7 and 8: 980481-001A vii
Page 9 and 10: IntroductionThis section describes
Page 11 and 12: Inspecting the PrinterLook at the o
Page 13 and 14: Closing the printerLower the top co
Page 15 and 16: Getting StartedThis section describ
Page 17 and 18: Loading Roll MediaWhen you load med
Page 19 and 20: Using the GuidesThe guides direct t
Page 21 and 22: Media Length SensingMOVIEBefore you
Page 23 and 24: USB Interface RequirementsUniversal
Page 25 and 26: Serial CommunicationsSerial communi
Page 27 and 28: Operation & OptionsThis section hel
Page 29 and 30: Printing in Peel-ModeThe optional d
Page 31 and 32: Using the Cutter OptionPrinters tha
Page 33 and 34: MaintenanceCleaningWhen you clean t
Page 35 and 36: Platen ConsiderationsThe standard p
Page 37 and 38: Replacing the Print HeadIn the even
Page 39 and 40: Replacing the LP Print Head (Contin
Page 41 and 42: TroubleshootingWhat the Status Ligh
Page 43 and 44: Media HandlingProblemPrinting conti
Page 45: The printing does not start at the
Page 49 and 50: AppendixInterfacesUniversal Serial
Page 51 and 52: ZebraNet® PrintServer II for Ether
Page 53 and 54: Serial (RJ-11) Alternative Connecto

Manual - LP2824 - logmaster

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?