910 aufst - Durkopp Adler AG

More documents

Recommendations

Info

General safety instructionsThe non-observance of the following safety instructions can causebodily injuries or damages to the machine.1. The machine must only be commissioned in full knowledge of theinstruction book and operated by persons with appropriate training.2. Before putting into service also read the safety rules andinstructions of the motor supplier.3. The machine must be used only for the purpose intended. Use ofthe machine without the safety devices is not permitted. Observe allthe relevant safety regulations.4. When gauge parts are exchanged (e.g. needle, presser foot, needleplate, feed dog and bobbin) when threading, when the workplace isleft, and during service work, the machine must be disconnectedfrom the mains by switching off the master switch or disconnectingthe mains plug.5. Daily servicing work must be carried out only by appropriatelytrained persons.6. Repairs, conversion and special maintenance work must only becarried out by technicians or persons with appropriate training.7. For service or repair work on pneumatic systems, disconnect themachine from the compressed air supply system (max. 7-10 bar).Before disconnecting, reduce the pressure of the maintenance unit.Exceptions to this are only adjustments and functions checks madeby appropriately trained technicians.8. Work on the electrical equipment must be carried out only byelectricians or appropriately trained persons.9. Work on parts and systems under electric current is not permitted,except as specified in regulations DIN VDE 0105.10. Conversion or changes to the machine must be authorized by usand made only in adherence to all safety regulations.11. For repairs, only replacement parts approved by us must be used.12. Commissioning of the sewing head is prohibited until such time asthe entire sewing unit is found to comply with EC directives.13. The line cord should be equipped with a country-specific mainsplug. This work must be carried out by appropriately trainedtechnicians (see paragraph 8).It is absolutely necessary to respect the safetyinstructions marked by these signs.Danger of bodily injuries !Please note also the general safety instructions.
IndexPage:Part 2: Installation Instructions cl. <strong>910</strong>1. Scope of delivery. ............................................. 32. General notes and securing devices ................................. 33. Mounting the stand and the control cabinet3.1 Tabletops................................................... 53.2 Mounting the parts of the stand ..................................... 53.3 Completingthetabletop.......................................... 63.4 Connecting the control box to the main switch ............................. 83.5 Mounting the stand and the reference value transmitter ....................... 93.6 Mounting the oil collector sump ...................................... 103.7 Adjustingtheworkingheight ....................................... 114. Mounting the sewing unit4.1 Mounting the oil pan ............................................ 124.2 Assemblyofthesewingunit........................................ 134.3 Mounting the control panel. ........................................ 144.4 Potential compensation .......................................... 154.5 Mounting the cover hood. ......................................... 1625. Connecting the plug connections to the control box5.1 Plug connections at the multiple pin strip (4-fold) ........................... 175.2 Plug connections at the multiple pin strip (15-fold) ......................... 185.3 Wiring..................................................... 196. Mounting the thread reel holder .................................... 197. Changing the sewing foot and the fabric clamps ......................... 208. Mounting the eye protection ...................................... 219. Oil lubrication9.1 Filling up oil. ................................................. 229.2 Oiling wicks and felt part (connecting rod) ............................... 239.3 Oiling the hook path. ............................................ 2410. Putting into operation10.1 Installationofthemachinesoftware................................... 2510.1.1 General notes ................................................ 2510.1.2 Loading the program ............................................ 2510.1.3 Dongle update via Internet. ........................................ 2610.3 Seamprogram................................................ 2710.4 Sewingtest ............................................. 2811. Optional equipment11.1 Sewinglamp................................................. 291
Page 1 and 2: 910CNC-Nähanlage für freie Nahtko
Page 3: ForewordThis instruction manual is
Page 7 and 8: 1. Scope of deliveryThe scope of de
Page 9 and 10: 3. Mounting the stand and the contr
Page 11 and 12: 8- Place the control box 8 on the u
Page 13 and 14: 3.5 Mounting the stand and the refe
Page 15 and 16: 3.7 Adjusting the working height122
Page 17 and 18: 4.2 Assembly of the sewing unit4 3
Page 19 and 20: 4.4 Potential compensation13 2- Fro
Page 21 and 22: 5. Connecting the plug connections
Page 23 and 24: 5.3 Wiring2In order to make it poss
Page 25 and 26: 8. Mounting the eye protection4321C
Page 27 and 28: 9.2 Oiling wicks and felt part (con
Page 29 and 30: 10. Putting into operation10.1 Inst
Page 31 and 32: 10.2 Seam programIf no seam program
Page 33 and 34: 11. Optional equipment11.1 Sewing l

910 aufst - Durkopp Adler AG

Create successful ePaper yourself

Delete template?

Save as template?