Hawke Transit System catalogo

More documents

Recommendations

Info

MARINE FRAME INSTALLATION INSTRUCTIONSInstallation MethodsA choice of Hawke Marine Frames isavailable to meet the varied criteria given byeach situation.Examples of frame installations are as follows,each method giving an inspectableprofessional finish to any cable penetration.FRAMEDIMENSION+ 1mm8mm8mmAPERTUREAPERTURE + 20 mmHMXHMFXFor HMX Frames.Bulkhead aperture diameter must be Framesize plus 1mm.See table on page 26.For HMFX Frames.A minimum clearance of 16 mm is requiredto both height and width dimensions as shown.STAY PLATE RETAINING LUGSCONTINUOS WELDCONTINUOS WELDPLAN VIEWHawke Marine Frames should be welded fromboth sides.Hawke Marine Frames can be offset from thehorizontal or vertical to reduce the bendingradius on cables passing through them.Note: When installing Marine Frames ensurethe edges of the frame are free of weldwhich could interfere with retaining lugs onstay and compression plates.CONTINUOS WELDHMFXCONTINUOS WELDHMBXCONTINUOS WELDHMEX22www.hawke-hts.com
FRAME WELDING INSTRUCTIONSHawkeMarine Transit SystemIf necessary, to reduce thegap add weld material tothis face (not to the frame)BULKHEAD OR DECK1mm MAXHAWKE TRANSIT FRAMEThe aperture in the bulkhead/deck should be cut out such that the gap surrounding theframe 1mm.If gap is in excess of 1mm weld material may be added to the bulkhead/deck cut faceto reduce the gap. The bulkhead/deck should then be dressed and prepared aspreviously stated.TACK WELDS TO POSITION FRAMEAND HELP PREVENT DISTORTION.FOR MULTIPLE FRAMES 1 TACKWELD PER APERTURE SHOULD BEADDED TOP & BOTTOMWELDS (A) AND (B)FILET WELDS (C) AND (D)Welding Instructions for Mildand Stainless Steel FramesPrior to any welding process the jointand surrounding area should beprepared. The area must be clean,dry and free from any oil, grease,scale or oxide and any otherdebris/contaminates that may affectweld performancee.g. protective coatings andprimers.(B) UNDERSIDE(D) TOPSIDE(A) UNDERSIDE(C) TOPSIDEFRAMES THICKNESS(10 MM FORMARINE FRAMES)STARTz= 1 / 2 T up toz max= 6 mmfor higher values of zmore than one runof filled weld maybe requiredPrior to completing welds on either side of the bulkhead the frame should be tackedinto position as in the sketch above. The tack welds reducing the amount of distortionin the parent metals.The frame must be welded from both sides of the bulkhead.Welding Sequence1st (A) underside, 2nd (B) underside,3rd (C) topside, 4th (D) topsideNote: Allow adequate time for cooling to prescribed levels to prevent cracking betweeneach weld run. Weld runs should not start or stop at a tack weld but should run overa tack.www.hawke-hts.com23
Page 2 and 3: H A W K E R O U N D , M A R I N E A
Page 4 and 5: WHAT IS A CABLE TRANSIT SYSTEM?A Tr
Page 6 and 7: TOLERANT BLOCK SIZE RANGEThis enabl
Page 8 and 9: SELECTION AND SPECIFICATION PROCEDU
Page 10 and 11: COMPRESSION SYSTEM COMPONENTSCompre
Page 12 and 13: H A W K E C I V I L T R A N S I T S
Page 14 and 15: C I V I L T R A N S I T S Y S T E M
Page 16 and 17: C I V I L F R A M E - D I M E N S I
Page 18 and 19: C I V I L T R A N S I T S Y S T E M
Page 20 and 21: H A W K E M A R I N E T R A N S I T
Page 24 and 25: M U L T I P L E F R A M E A P PFRAM
Page 26 and 27: MARINE FRAME - DIMENSIONAL DATA26ww
Page 28 and 29: 28H A W K E R O U N D T R A N S I T
Page 30 and 31: T R A N S I T I N S T A L L A T I O
Page 32 and 33: T H E H A W K E E M C T R A N S I T
Page 34 and 35: EMC TRANSIT SYSTEM INSTALL ATION GU
Page 36: HAWKE TRANSIT SYSTEM - HTSHead Offi

Hawke Transit System catalogo

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?