Hawke Transit System catalogo

More documents

Recommendations

Info

T R A N S I T I N S T A L L A T I O N G U I D ERound TransitSystemThe following diagrams explain step by step how easy it is to installHawke cable/pipe tolerant blocks into Round Transit frames.1Draw up a Hawke Design Templateto determine your cable/pipe layout.2Measure the inside of pipe oraperture to ensure that it is withinthe tolerance of the Round TransitFrame to be used.3Insert the Round Transit Frame andopen the two front plate*. Nolubricant should be applied to theaperture or outside of the frameHawke Cable/Pipe/BlockSelection Gauge1. Simply wrap the gauge tightlyaround the cable or pipe from themeasurement line.2. Reading along themeasurement line will reveal thecorrect block size for the cable orpipe and identify it by colourcode.4Pull the cables or pipes throughthe frame. (Note: Use open endedRound Transit to fit around existingcables/pipes).Lubricate the inside of the frame5 and each of the insert blocks.6Begin packing the transit framestarting at the bottom andfinishing at the top. Ensure that theblocks are pushed firmly against therear retaining lip.e.g. 4022 REDWhere there is an overlapbetween two block sizes e.g.6052 or 9053, either size can beselected to best use the availablespace in the transit frame.7Slide the two front plates togetherand tighten the nuts 2mmeach time, applying equal pressure toboth plates*. The bolts should betightened until the cables/pipes aresealed. A minimum of 10mm of threadshould protrude on each bolt.8Hawke’s unique colour codingsystem enables the installationto be visually inspected aftercompletion and ensures the correctmatching of the block halves.9EXTRACTION OF SYSTEMExtraction is achieved by releasing thecompression, i.e. by reversing steps 5 and6 and screwing M8 bolts(not supplied) intothe threaded holes at each corner of thefront plates. This releases the assemblyfrom the aperture and allows the systemto be disassembled.Hawke Cable/Pipe Tolerant BlocksHawke's unique inspectable colour codedblocks ensure that the top and bottom halfof each block has been correctly matchedfor size.* Note: HRT30, HRT40 and HRT50 front plates are fixed30www.hawke-hts.com
H R T A P P L I C A T I O N SHawkeRound Transit SystemCast PipeWelded TubeHRT ApplicationsThe HRT is certified for use in civiland marine installations.The HRT seals cables or pipeswithin cast pipes, welded tubes orcore drilled holes.Core Drilled HoleTRANSIT ASSEMBLY CHECKLIST1.Measure the outside diameter of each cable and ensure that the diameter iswithin the cable range marked on the front of the block that seals each cable.2.Check that all colour codes on the block pairs are matching.3.Check that there are sufficient blocks installed into the frame and that thereare no gaps not sealed by blocks.4.If the transit application is in excess of 3.5 bar high pressure stayplatesshould be used ref. 931p, together with an extra 5mm sealing strip.5.Check the correct amount of compression has been applied to the end packer bolts,10mm of thread on each bolt should be protruding.www.hawke-hts.com31
Page 2 and 3: H A W K E R O U N D , M A R I N E A
Page 4 and 5: WHAT IS A CABLE TRANSIT SYSTEM?A Tr
Page 6 and 7: TOLERANT BLOCK SIZE RANGEThis enabl
Page 8 and 9: SELECTION AND SPECIFICATION PROCEDU
Page 10 and 11: COMPRESSION SYSTEM COMPONENTSCompre
Page 12 and 13: H A W K E C I V I L T R A N S I T S
Page 14 and 15: C I V I L T R A N S I T S Y S T E M
Page 16 and 17: C I V I L F R A M E - D I M E N S I
Page 18 and 19: C I V I L T R A N S I T S Y S T E M
Page 20 and 21: H A W K E M A R I N E T R A N S I T
Page 22 and 23: MARINE FRAME INSTALLATION INSTRUCTI
Page 24 and 25: M U L T I P L E F R A M E A P PFRAM
Page 26 and 27: MARINE FRAME - DIMENSIONAL DATA26ww
Page 28 and 29: 28H A W K E R O U N D T R A N S I T
Page 32 and 33: T H E H A W K E E M C T R A N S I T
Page 34 and 35: EMC TRANSIT SYSTEM INSTALL ATION GU
Page 36: HAWKE TRANSIT SYSTEM - HTSHead Offi

Hawke Transit System catalogo

Create successful ePaper yourself

Delete template?

Save as template?