Reactive Power Controller Operating instructions

More documents

Recommendations

Info

Reactive Power ControllerServiceIf certain questions appear, which are not mentioned inthis handbook, please call us directly.To be able to support you, we require the followinginformation:- Device description (see type plate),- Serial number (see type plate),- Software Release,- Measurement and supply voltage and- Exact description of the error.You can reach us:Monday to Thursday from 07:00 to 15:00and on Friday from 07:00 to 12:00Janitza electronics GmbHVor dem Polstück 1D-35633 LahnauSupport:Tel. (0 64 41) 9642-22Fax (0 64 41) 9642-30e-mail: info@janitza.dePage 16= Key 1 = Key 2 = Key 3
Reactive Power ControllerDisplay and useIn the front side of Prophi there is a digital indicationand three keys, with which you can question data andprogram the device.If you are in automatical mode, you can change betweenthe operating modes using key 1:automatic mode,manual mode,standard programming andexpanded programmingautomatic modemanual modestandard programmingexpanded programmingϕ1 ϕ2 learn 1:1... ProgIn standard programming often needed settings are carriedout such as current transformer ratio or the numberof stages.In expanded programming those settings are carried out,which are used not as often, such as discharge time orchoke degree.Automatic modeAutomatic mode is marked by the symbol .In automatic mode, there is:- the switching condition of capacitive stages,- the actual value of cos(phi) indicated,- Connection and disconnection of capacitive stages,- all 15 minutes saving ofpeak and lowest values,number of switchings of the capacitor stages andthe switching times of capacitor stages.- Indication of measured values using key 2 and 3.There are three possibilities to reach automatic mode:- after net return,- pressing key 1 for about 2 seconds,- pressing no key in programming mode for 1Automatic modecosϕind1 2 3ϕ1Actual value cos(phi)To reach the expanded programming from automaticmode, leaf through the standard programming using key1 until the symbol "Prog" appears. Confirm selectionwith key 2, and you are in expanded programming.Manual modeIn manual mode, you can switch in capacitor stagesusing key 3, and switch off capacitor stages using key2. The time between two switchings is only limited bythe programmed discharge time. If one stage shall beconnected in manual mode and a discharge time is running,the number and capacitor stage is flashing.If no capacitors are switched in manual mode, anautomatical jumpback to automatical mode is carriedout after 15 minutes.Connected stages1 2 3 4 5indk VArManual modeReactive power= Key 1 = Key 2 = Key 3Page 17
Page 1 and 2: Reactive Power ControllerOperating
Page 3 and 4: Reactive Power ControllerDisplay ov
Page 5 and 6: Reactive Power ControllerProduct de
Page 7 and 8: Reactive Power ControllerProphiDiag
Page 9 and 10: Reactive Power ControllerSum curren
Page 11 and 12: Reactive Power ControllerCurrent me
Page 13 and 14: Reactive Power ControllerTarget-cos
Page 15: Reactive Power ControllerRemoval of
Page 19 and 20: Reactive Power ControllerStandard p
Page 21 and 22: Reactive Power ControllerLearning o
Page 23 and 24: Reactive Power ControllerSwitching
Page 25 and 26: Reactive Power ControllerExpanded p
Page 27 and 28: Reactive Power ControllerPower stat
Page 29 and 30: Reactive Power ControllerVoltage tr
Page 31 and 32: Reactive Power ControllerSwitching
Page 33 and 34: Reactive Power ControllerLower volt
Page 35 and 36: Reactive Power ControllerVentilator
Page 37 and 38: Reactive Power ControllerOvertemper
Page 39 and 40: Reactive Power ControllerPasswordTh
Page 41 and 42: Reactive Power ControllerReset prog
Page 43 and 44: Reactive Power ControllerSoftware r
Page 45 and 46: Reactive Power ControllerBaud rateT
Page 47 and 48: Reactive Power ControllerTable Prof
Page 49 and 50: Reactive Power ControllerDiagr.: Me
Page 51 and 52: Reactive Power ControllerDisplay in
Page 53 and 54: Reactive Power ControllerConfigurat
Page 55 and 56: Reactive Power ControllerBack SideS

Reactive Power Controller Operating instructions

Create successful ePaper yourself

Delete template?

Save as template?