MEMOLUBÂ® User's Guide - PLI, LLC

More documents

Recommendations

Info

Lubrication SystemsMEM LUB ® 2-Point MEMOLUB ® SystemSPLT-0307-PG4 Copyright©2006 PLI, LLC All Rights ReservedHow the Splitter MEMO WorksThe Valve Stem is maintained in the upper position by the spring. When the MEMOLUB® HPS ejects lubricant,the MEMOLUB® HPS pump piston simultaneously pushes the Valve Stem downwards. Lubricant flows throughthe hollow Valve Stem and, as shown in stage 1, out through Outlet 1. As the Valve Stem moves downwards,Outlet 1 is closed and Outlet 2 opens allowing lubricant to flow through it, as shown in stage 2. Upon completionof the output cycle the Return Spring pushes the Valve Stem into the upper position to complete the cycle.Stage 1Stage 2Discharge PortCap3.31"84mmValve StemReturn SpringBodyOutlet 2Outlet 1Outlet 2Outlet 11.57"40mm1.22"31mmMounting DimensionsGigaMegaStandardMEMOLUB MEI MEIMEI7.5" (19cm)8.75" (22.23cm)12" (30.48cm)4.00" 4.75"10.16cm12.07cmMEMOLUB® User's Guide Page 29 of 39 PLI, LLC
MEM LUB ® Lubrication Systems Maintenance AdapterDoc: MLMAINTAD07 Copyright©2006 PLI, LLC All Rights ReservedPre-charging and Annual Maintenance of Lubrication SystemsThe Maintenance Adapter can be used to “pre-charge” a remote line or a distribution blockand its associated lines. This pre-charge procedure may become necessary during initialequipment installation or when changing the type of grease being used. It can also be used toconveniently add grease to a bearing on which the MEMO has already been installed. TheMaintenance Adapter has a M12 x 1.50 female thread, which matches the male thread of thebrass MEMO fitting.The Maintenance Adapter is also useful in flushing old grease from remote lines anddistribution systems. It is recommended that this procedure be performed on an annual basisto eliminate the potential problems associated with grease/oil separation that can occur withsome greases.MEMOLUB® Multi-Point Systems ordered as a Plug’n Lube system, with tubing that hasbeen pre-filled at the factory, already contains the correct lubricant and does not require fillingin the field during installation.Note: The Maintenance Adapter is not to be used with the 2-Point Splitter System. Pleaserefer to Section 3.3 for information on the proper procedure to be used in priming the Splitter-MEMO.Grease FittingMaintenance AdapterBrass MEMO FittingTiming Ring HolderIf additional Maintenance Adapters are needed they can be ordered as part number: OPMAINTADPTMEMOLUB® HPS User's Guide Page 30 of 33 PLI, LLC
Page 4: 1 The MEMOLUB ® HPS1.1 OverviewThe
Page 11 and 12: attery power and under control of t
Page 13 and 14: shaped lock washer) inserted into t
Page 15 and 16: 6.2 Opening and Closing the MEMOLUB
Page 17 and 18: 6.4 Installing an Oil CartridgeInst
Page 19 and 20: 7.4 Mounting with the Progressive D
Page 21 and 22: APPENDIXMEMOLUB ® HPS User’s Gui
Page 23 and 24: MEM LUB ® Lubrication SystemsDimen
Page 25 and 26: MEM LUB ® Lubrication Systems Fine
Page 27 and 28: MEM LUB ® Lubrication Systems Mult
Page 29: MEM LUB ® Lubrication Systems 2-Po
Page 33 and 34: MEM LUB ® Lubrication SystemsInsta
Page 35 and 36: MEM LUB ® Lubrication SystemsHazar
Page 37 and 38: MEM LUB ® Lubrication Systems Exte
Page 39 and 40: MEM LUB ® Lubrication Systems MEMO

MEMOLUBÂ® User's Guide - PLI, LLC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?