RULES DET NORSKE VERITAS (DNV) = STRUCTURES = - Boat Design Net

More documents

Recommendations

Info

Amended July 2011, see page 3 Rules for High Speed, Light Craft and Naval Surface Craft, January 2011Pt.3 Ch.1 Sec.2 – Page 17Fig. 6Waterline angle γ302 Forebody side and bow pressure shall not be taken less than according to 500.303 The impact pressure according to 301 is be calculated for longitudinal positions between 0.4 L and bow.304 In vertical direction the impact pressure shall extend from bottom chine or upper turn of bilge to maindeck or vertical part of craft side.Upper turn of bilge shall be taken at a position where deadrise angle reaches 70°, but not higher than thewaterline.If no pronounced bottom chine or upper turn of bilge is given (V-shape), the impact pressure shall extend fromkeel to main deck or vertical part of craft side.C 400 Slamming pressure on flat cross structures401 The design slamming pressure on flat cross structures (catamaran tunnel top, etc.), shall be taken as:P sl 2.6 k Δt--- 0.3 H C=a Acg 1 – ------ ( kN ⁄ m 2 ) H LA = design load area for element considered. See 201H C = minimum vertical distance in m from WL to load point in operating conditionk t = longitudinal pressure distribution factor according to Fig.7H L = necessary vertical clearance in m from WL to load point to avoid slamming= 0.22 L 0.8k c – ----------- L 1000 k c = hull type clearance factor0.3 for catamaran, wave piercer0.3 for SES, ACV0.3 for hydrofoil, foilcatamaran0.5 for SWATH.DET NORSKE VERITAS AS
Rules for High Speed, Light Craft and Naval Surface Craft, January 2011 Amended July 2011, see page 3Pt.3 Ch.1 Sec.2 – Page 181.5k tSWATH1.00.5CATAMARANWAVE PIERCERSESACVHYDROFOILFOILCATAP 0.5L FPFig. 7Flat cross structure slamming distribution factor k t402 Slamming pressure shall not be less than the sea pressure according to 500 (side above WL).C 500 Sea pressure501 Pressure acting on the craft’s bottom, side (including superstructure side) and weather decks shall betaken as:— for load point below design waterline:— for load point above design waterline:Minimum sea pressures are given in Table C1.Table C1 Minimum sea pressuresNotationSidesWeatherdecksR0, R1, R2, R3 6.5 5 3R4 5 4 3R5-R6 4 3 3h 0k sp 10h 0 k s 1.5 h 0= + – ---- CW ( kN ⁄ m 2 ) T p = a k s ( C W – 0.67 h 0 ) ( kN ⁄ m 2 )Roofs higher than 0.1 Labove WL= vertical distance in m from the waterline at draught T to the load point= 7.5 aft of amidships=5/C B forward of FP.Between specified areas k s shall be varied linearly, see Fig.8a = 1.0 for craft’s sides and open freeboard deck= 0.8 for weather decks above freeboard deckC W = wave coefficient according to A200.DET NORSKE VERITAS AS
Page 1 and 2: RULESDET NORSKE VERITAS (DNV)= STRU
Page 3 and 4: FOREWORDDET NORSKE VERITAS (DNV) is
Page 5 and 6: Rules for High Speed, Light Craft a
Page 17: Rules for High Speed, Light Craft a
Page 29 and 30: FOREWORDDET NORSKE VERITAS (DNV) is
Page 69 and 70:
Rules for High Speed, Light Craft a
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83:
show all

RULES DET NORSKE VERITAS (DNV) = STRUCTURES = - Boat Design Net

Create successful ePaper yourself

Delete template?

Save as template?