Installation and Assembly - Universal Articulating

More documents

Recommendations

Info

WARNING• Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV.6Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread.SWIVEL BOXC.25"F6-16-2Hook tilt-roll assembly (B) onto M10 screws (F).Insert carriage bolt (I) into slot of swivel box asshown in figure 6.1. Install nylon washer (G) and tiltadjustment knob (H).Install remaining two M10 screws (F) as shown infigure 6.2. HAND TIGHTEN all four M10 screws toallow for tilt adjustment. Remove tape from carriagebolt (I). For tilt adjustment, push back on the top ofplasma to relieve pressure on knob. Adjust tilt todesired position and tighten tilt adjustment knob (H),then securely tighten all four M10 screws (F) using 6mm allen wrench (U).SWIVEL BOXIGHCAUTION• After tilt is adjusted, all fasteners must be tightened.Failure to do so will result in damage to the mount.IHFBFfig 6.1 fig 6.2Adapter bracket not shown for clarity.Adapter bracket not shown for clarity.10 of 13 ISSUED: 06-05-06 SHEET #: 202-9141-3 08-17-06
Installing Adapter Brackets7Refer to Screen Compatibility Chart to determine the proper fasteners to use.To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Placescreen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown in figure7.1. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers,and spacers as shown in figure 7.3.Note: Top and bottom holes must always be used.Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.Note: If using security screws, tighten using security allen wrench (DD).WARNING• Tighten screws so adapter brackets are firmlyattached. Do not tighten with excessive force.Overtightening can cause stress damage to screws,greatly reducing their holding power and possiblycausing screw heads to become detached. Tighten to40 in. • lb (4.5 N.M.) maximum torque.BBorCCCENTER BRACKETSVERTICALLY ON BACK OFSCREENXNotes:• The number of fasteners used will vary,depending upon the type of screen.• Multi-washers and spacers may not beused, depending upon the type of screen.• Use the corresponding hole in the multiwasherthat matches your screw size asshown in figure 7.2.fig 7.1XNote: "X" dimensions should be equal.WARNING• If screws don't get three complete turns in the screeninserts or if screws bottom out and bracket is still nottightly secured, damage may occur to screen orproduct may fail.BB or CCSCREWSMULTI-WASHERMEDIUM HOLE FOR M5 SCREWSMULTI-WASHERSPACERSSMALL HOLE FOR M4 SCREWSLARGE HOLE FOR M6 SCREWSfig. 7.2fig 7.311 of 13 ISSUED: 06-05-06 SHEET #: 202-9141-3 08-17-06
Page 1 and 2: Installation and Assembly - Univers
Page 3 and 4: Wall Mount Parts ListRTPLA 60-SBefo
Page 5 and 6: Security Adapter Bracket FastenersM
Page 7 and 8: Installation to Concrete WallWARNIN
Page 9: 44-1Attach two pieces of vinyl trim

Installation and Assembly - Universal Articulating

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?