LAN Configuration

More documents

Recommendations

Info

‚M’, ‚m’, ‚F’, ‚f’ Keeping byte TX.DWNR, RX.DWNR ‚T’, ‚t’ Timer TX.DWNR, RX.DWNR ‚Z’, ‚z’, ‚C’, ‚c’ Counter TX.DWNR, RX.DWNR � Status values (TXSTATUS, RXSTATUS) Status values Description 0000h Instruction completed 7000h Instruction will not be processed. 80B0h Construction component does not know the record. 80B1h Wrong length in the parameter. 80C3h Memory temporary used. 80C4h Communication error. 8183h Project planning’s not available or service has not been started yet. 8184h Data type or source data range is wrong. 8185h Length exceeds the maximum size of the source data range or the destination data range is too small. � Function blocks o FC 55 (S7<strong>LAN</strong>_SEND) o FC 56 (S7<strong>LAN</strong>_RECV) These function blocks are used to send and receive data. Page 40 Cable and adapter manual © by PI 2008
1.6.5. CP – Mode with ProTool/Pro CS v6.00 Used Software: ProTool/Pro CS v6.00 SP2 1. Creating a new project Start the ProTool/Pro CS software and click on File � New. (for more Information about creating projects with ProTool/Pro CS v6.00 read the manual of the developer). 2. Choosing a destination device The destination device must support the Ethernet interface. 3. Choosing a PLC Enter a typical PLC Name and select the used PLC type (e.g. „SIMATIC S7 300/400 V6.0“). After choosing the PLC type click on parameter. OP parameter Interface If the desired destination device supports “Ethernet” you can change the interface to “Ethernet”. Protocol Communication is established by using the IP protocol. Address Enter the IP address of your computer. Subnet mask Enter the subnet mask of your computer. Routing Activate this check box to reach members outside your subnet. Requires that the construction components of © by PI 2008 Cable and adapter manual Page 41
Page 1 and 2: Version: 4.9 18.04.2008 Cable and a
Page 3 and 4: 4.7.2. Ports.......................
Page 5 and 6: 1.1. Description The MPI - LAN cabl
Page 7 and 8: MPI - LAN connected with the comput
Page 9 and 10: 1.4. Installation Hardware Connect
Page 11 and 12: . Default display (Menu Messages) F
Page 13 and 14: 1.6. Operating instructions Be sure
Page 15 and 16: a. PG 2000 (v4.41) 1. Start the PG
Page 17 and 18: TCP/IP RFC1006 Communication 6. Cli
Page 19 and 20: TCP/IP RFC1006 Configuration 16. Fo
Page 21 and 22: 8. Now you should expand in the „
Page 23 and 24: To clean up errors faster the WinCC
Page 25 and 26: e. Windows Control Center flexible
Page 27 and 28: 9. Press the button „Transfer“
Page 29 and 30: 10. If you want to transfer you pro
Page 31 and 32: If you skipped the point b („Set
Page 33 and 34: 7. In the registry path „Local De
Page 35 and 36: i. S7 for Windows v5.02 Please be s
Page 37 and 38: 1.6.4. Merge two PLCs together by u
Page 39: Data exchanging with the help of th
Page 43 and 44: 1.6.6. Option Watchdog With this Op
Page 45 and 46: int main(int argc, char* argv[]) {
Page 47 and 48: � °Config° MPI-BUS° MPI interf
Page 49 and 50: • Protocol Change the protocol ve
Page 51 and 52: 1.8. Technical data Type Technical
Page 53 and 54: 2. S7 - LAN Ord. No. 9352 - LANCon
Page 55 and 56: 2.3. Connection possibilities S7 -
Page 57 and 58: S7 - LAN connection possibilities w
Page 59 and 60: 2.5. Control elements LED for the n
Page 61 and 62: 2.6.1. Using the PLC-VCOM software
Page 63 and 64: 6. Now the software is ready to est
Page 65 and 66: TCP/IP RFC1006 Communication 6. Cli
Page 67 and 68: TCP/IP RFC1006 Configuration 16. Fo
Page 69 and 70: 8. Now you should expand in the „
Page 71 and 72: To clean up errors faster the WinCC
Page 73 and 74: e. Windows Control Center flexible
Page 75 and 76: 9. Press the button „Transfer“
Page 77 and 78: 10. If you want to transfer you pro
Page 79 and 80: If you skipped the point b („Set
Page 81 and 82: 7. Confirm your settings with „OK
Page 83 and 84: i. S7 for Windows v5.02 Please be s
Page 85 and 86: 2.6.3. Direct communication using T
Page 87 and 88: 10. Type in the edit box “Name“
Page 89 and 90: 17. Select the registry card “Ass
Page 91 and 92:
24. A new window opens (the hardwar
Page 93 and 94:
28. Right click on “CPU 312“ in
Page 95 and 96:
33. After you have saved the networ
Page 97 and 98:
2.6.4. Merge two PLCs together by u
Page 99 and 100:
� Format of TXERRRDY and RXERRRDY
Page 101 and 102:
the station supports routing (CPUs
Page 103 and 104:
The S7/MPI-LAN sends only data when
Page 105 and 106:
2.7. Technical data Type Technical
Page 107 and 108:
TS-Function Switches the TeleServic
Page 109 and 110:
MPI/PROFIBUS The MPI/PROFIBUS needs
Page 111 and 112:
Display In this Dialog you could re
Page 113 and 114:
Address Format Input Description FB
Page 115 and 116:
The following operands are possible
Page 117 and 118:
Password Description General Access
Page 119 and 120:
4.1. Description The S5 - LAN modul
Page 121 and 122:
S5 - LAN module connected to the co
Page 123 and 124:
4.4. Installation Hardware The S5 -
Page 125 and 126:
2. To start the driver installation
Page 127 and 128:
4.6. Operating instructions Be sure
Page 129 and 130:
4.6.3. Using a PLC software a. PG 2
Page 131 and 132:
. SIMATIC Step© 5 Manager (v5.2 +
Page 133 and 134:
c. Windows Control Center (WinCC) (
Page 135 and 136:
d. Windows Control Center flexible
Page 137 and 138:
9. Press the button „Transfer“
Page 139 and 140:
7. In the main window start the Tra
Page 141 and 142:
5. After the software is configured
Page 143 and 144:
8. Select the network interface car
Page 145 and 146:
4.6.5. S5 - Gateway communication R
Page 147 and 148:
4.6.5.1. Specifications of the conf
Page 149 and 150:
In the following example the DB20 w
Page 151 and 152:
4.7.1. Principle Schematics of the
Page 153 and 154:
5.1. Description The MPI - USB cabl
Page 155 and 156:
MPI - USB connected to the computer
Page 157 and 158:
5.4. Installation Hardware Normal i
Page 159 and 160:
. Default Display (Menu Messages) F
Page 161 and 162:
5.6. Operating instructions Be sure
Page 163 and 164:
a. PG 2000 (v4.41) 1. Start the PG
Page 165 and 166:
6. Back in the „Set PG/PC interfa
Page 167 and 168:
c. SIMATIC Step© 7 Manager (v5.2 +
Page 169 and 170:
e. Windows Control Center flexible
Page 171 and 172:
9. Press the button „Transfer“
Page 173 and 174:
8. In the main window start the Tra
Page 175 and 176:
If you skipped the point b („Set
Page 177 and 178:
7. In the registry path „Local De
Page 179 and 180:
i. S7 for Windows v5.02 Please be s
Page 181 and 182:
5.6.4. Configuring the operator pan
Page 183 and 184:
. Info Select the menu “Info“ t
Page 185 and 186:
the cables menu) “Lock” in the
Page 187 and 188:
5.8. Technical data Type Technical
Page 189 and 190:
6. PLC - VCom 6.1. Description The
Page 191 and 192:
to go on. 7. After the driver has b
Page 193 and 194:
16. Now the “Hardware - Assistent
Page 195 and 196:
In the section state the first thin
Page 197 and 198:
With a press on OK the PLC - VCom s
Page 199 and 200:
6 Click on Settings to configure th
Page 201 and 202:
7. MPI_DP_PPI Driver 7.1. Descripti
Page 203 and 204:
USB - Driver installation (for MPI
Page 205 and 206:
7.4. Properties If you pressed the
Page 207 and 208:
7.5. extended Properties In this di
Page 209 and 210:
Select then „MPI_DP_PPI Treiber f
Page 211:
Q: My cable is connected with the S
show all

LAN Configuration

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?