CRT 48 Operation - Wacker Neuson

More documents

Recommendations

Info

Safety Information CRT 48 Ref. Label Meaning F WARNING! Read and understand the supplied Operator’s Manual before operating the machine. Failure to do so increases the risk of injury to yourself or others. G WARNING! Hot surface! H WARNING! Cutting hazard. Always replace blade guard! J WARNING! Pressurized contents. Do not open when hot! K WARNING! Hand injury if caught in moving belt. Always replace beltguard. L CAUTION! Lifting point. M Tie-down point. 14
CRT 48 Safety Information Ref. Label Meaning N Key switch, engine start: Off On Start O Operator’s Manual must be stored on machine. Replacement Operator’s Manual can be ordered through your local Wacker Neuson distributor. P WARNING! 4 A � � L A F = � B H � � J H � M A � > A B � H A � E B J E � C � = ? D E � A � L A H D A = @ � 2 = � I ? = � B = � � = � @ ? = K I A @ A = J D � H I A H E � K I E � � K H O E B = F A H I � � E I D E J � / � A E J I ? D A E > A L � � * A J � � C � � J J A H A � J B A H � A � > A L � H @ = I / A H � J K > A H � � F B D � D A C A D � > A � M E H @ � / � A E J I ? D A E > A � = � � B = � � A � K � @ I ? D M A H A 8 A H � A J � K � C � @ A H 6 � @ L A H K H I = ? D A � M A � � 2 A H I � � = � C A J H � B B A � M E H @ � 3 K E J A A � @ E I ? � @ A B � � J = ? E � � = � J A I @ A � A L = � J = H � = � � G K E � = = � E I = @ � H = @ A D � H � E C � � � � � I @ E I ? � I F � @ H � = � ? = A H O � = J = H � � = I J E � = H I A H E = � A � J A = K � = F A H I � � = G K A I A A � ? K A � J H A ? A H ? = � ) L = � J @ A � A L A H � \ = F F = H A E � = K � @ A I I K I @ A L � J H A J � J A � � J A H � A @ E I G K A @ A J = � � ? D = C A @ A � = J H K A � � A � � A @ E I G K A @ A J = � � ? D = C A F A K J J � � > A H A J A � J H = � � A H @ A C H = L A I > � A I I K H A I � K � � � A � = � � H J � wc_si000188gb.fm 15 & $ & & Remove pan from trowel before lifting machine overhead. Pans can fall and cause death or serious injury if a person is hit. (Located on top side of float pan.) Q Blade pitch control. Turn both controls inward to increase blade pitch. Refer to section Pitch Adjustment. R CAUTION! Engine oil pressure is low! Stop the engine and check the oil level. S CAUTION! Low voltage! Stop the engine and check the charging system.
Page 1: OPERATOR’S MANUAL 0 1 6 3 2 0 4 E
Page 4 and 5: wc_tx000001gb.fm 4
Page 6 and 7: Table of Contents CRT 48 3.12 Spark
Page 8 and 9: Safety Information CRT 48 1.2 Opera
Page 10 and 11: Safety Information CRT 48 1.4 Servi
Page 12 and 13: Safety Information CRT 48 W H V M J
Page 16 and 17: Safety Information CRT 48 Ref. Labe
Page 18 and 19: Safety Information CRT 48 Notes 18
Page 20 and 21: Operation CRT 48 2.2 Features and C
Page 22 and 23: Operation CRT 48 2.3 New Machines S
Page 24 and 25: Operation CRT 48 2.7 Stopping 2.8 O
Page 26 and 27: Operation CRT 48 b 2.10 Pitch Adjus
Page 28 and 29: Maintenance CRT 48 3.2 Trowel Gearb
Page 30 and 31: Maintenance CRT 48 3.3 Control Link
Page 32 and 33: Maintenance CRT 48 3.7 Blade Arm Ad
Page 34 and 35: Maintenance CRT 48 3.10 Drive Belt
Page 36 and 37: Maintenance CRT 48 3.12 Spark Plug-
Page 38 and 39: Maintenance CRT 48 3.14 Engine Oil
Page 40 and 41: Maintenance CRT 48 3.15 Engine Oil
Page 42 and 43: Maintenance CRT 48 Problem Reason R
Page 44 and 45: Technical Data CRT 48 4.2 Trowel Pa
Page 48 and 49: Trowel.qxd 11/24/04 10:18 AM Page 1
Page 60 and 61: AEM_ConcretePowerTrowel.qxd 7/23/03
Page 62: Wacker Construction Equipment AG ·

CRT 48 Operation - Wacker Neuson

Create successful ePaper yourself

Delete template?

Save as template?