CRT 48 Operation - Wacker Neuson

More documents

Recommendations

Info

Operation CRT 48 2.7 Stopping 2.8 Operation To stop trowel movement, return control levers to their neutral position and release pressure on the throttle foot pedal. To stop the engine, turn the keyswitch to “O” (off). To utilize your Wacker Neuson Ride-On Trowel to its fullest capacity, the machine should be driven in the direction that the operator is facing. This will finish the widest possible area, while giving the operator an excellent view of the slab surface about to be troweled. When the machine reaches the end of the slab, make a 180° U-turn, and repeat the straight line of direction to the other end of the slab. Note: During the break-in period, run the engine at 50% of full throttle. Refer to Section New Machines. NOTICE: DO NOT use excessive pressure on the control levers. Excessive pressure does not increase the reaction time of the machine and can damage the steering controls. NOTICE: Attempting to use the trowel too early in the curing stage of the concrete may result in an undesirable finish. Only experienced concrete finishers should operate the trowel. wc_tx000641gb.fm 24
CRT 48 Operation 2.9 Steering See Graphic: wc_gr000689 Refer to the illustration for the necessary hand motions to move the trowel in the desired direction, described below. 1 - forward 2 - reverse 3 - rotate clockwise 4 - rotate counter-clockwise 5 - left sideways 6 - right sideways ! " # $ wc_tx000641gb.fm 25 M ? � C H $ & '
Page 1: OPERATOR’S MANUAL 0 1 6 3 2 0 4 E
Page 4 and 5: wc_tx000001gb.fm 4
Page 6 and 7: Table of Contents CRT 48 3.12 Spark
Page 8 and 9: Safety Information CRT 48 1.2 Opera
Page 10 and 11: Safety Information CRT 48 1.4 Servi
Page 12 and 13: Safety Information CRT 48 W H V M J
Page 14 and 15: Safety Information CRT 48 Ref. Labe
Page 16 and 17: Safety Information CRT 48 Ref. Labe
Page 18 and 19: Safety Information CRT 48 Notes 18
Page 20 and 21: Operation CRT 48 2.2 Features and C
Page 22 and 23: Operation CRT 48 2.3 New Machines S
Page 26 and 27: Operation CRT 48 b 2.10 Pitch Adjus
Page 28 and 29: Maintenance CRT 48 3.2 Trowel Gearb
Page 30 and 31: Maintenance CRT 48 3.3 Control Link
Page 32 and 33: Maintenance CRT 48 3.7 Blade Arm Ad
Page 34 and 35: Maintenance CRT 48 3.10 Drive Belt
Page 36 and 37: Maintenance CRT 48 3.12 Spark Plug-
Page 38 and 39: Maintenance CRT 48 3.14 Engine Oil
Page 40 and 41: Maintenance CRT 48 3.15 Engine Oil
Page 42 and 43: Maintenance CRT 48 Problem Reason R
Page 44 and 45: Technical Data CRT 48 4.2 Trowel Pa
Page 48 and 49: Trowel.qxd 11/24/04 10:18 AM Page 1
Page 60 and 61: AEM_ConcretePowerTrowel.qxd 7/23/03
Page 62: Wacker Construction Equipment AG ·

CRT 48 Operation - Wacker Neuson

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?