CONSTRUCTION CHEMICALS

More documents

Recommendations

Info

PACKAGING MegaSıva Saten is delivered in net 20 kg kraft bags, which are stowed in 60 pcs. on a 80 cm x 100 cm palette (1200 kg). SHELF LIFE The shelf life of the product is 12 months when stored within non tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. STORAGE CONDITIONS The product should be stored within non tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. It should not be exposed to direct sunlight. The container of the product should be closed firmly when not used. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application. 121
MegaSıva Perlitli Cement Based, Manually Applied Fine Plaster With Pearlite PRODUCT DESCRIPTION Cement based pre-final coat surface preparation plaster with enhanced adherence, applied manually, which has been reinforced with various chemical additives. AREAS OF USE MegaSıva Perlitli is applied in indoors and outdoors spaces, on prime coated gas concrete and prime coated concrete surface and ceilings and on any roughcast (MegaSıva K, MegaSıva Makine İç, MegaSıva Makine Dıº, MegaSıva Elyaflı K) applied surfaces. PRODUCT ADVANTAGES • Ensuring high bonding to the surface, the product does not cause spalling and poses high bonding strength. • Being a high performance product, it does not cause contractions. • Prepared and applied easily. PERFORMANCE Dry bulk density 1.40 ± 0.1 gr/cm 3 TS EN 1015 - 10 Compressive strength CS III TS EN 1015 - 11 Bonding strength > 0.5 N/mm 2 TS EN 1015 - 12 Capillary water absorption coefficient W 1 TS EN 1015 - 18 Water vapor permeability µ < 11 TS EN 1015 - 19 Air content % 8.5 ± 0.5 TS EN 1015 - 7 > 5 hours (at 20 ± 5°C Workability time temperature and minimum 95 % TS EN 1015 - 9 relative humidity) Reaction to fire A1 TS EN 13501 - 1 The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. REFERENCE STANDARDS Certifications/Standards TS EN 998 - 1 (GP) Ministry of Public Works and Settlement Item No. Ministry of Public Works and Settlement Item No.: 04.476/D QUALITY CERTIFICATES Conformant to TS EN 998 - 1. CE APPLICATION PROCEDURE Application Surfaces Indoors and Outdoors Walls; - Gas concrete (MegaFilm primer applied) - Concrete (MegaFilm or MegaFilm BB primer applied) - Roughcast applied surfaces Ceilings; - Roughcast applied surfaces Surface Preparation • The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface. • The surface defects, which are deeper than 1 cm, should be repaired with MegaTamir İ or MegaTamir K 24 hours in advance. In the cases, where structural repair mortar should be used; MegaTamir İ Yapısal or MegaTamir K Yapısal should be preferred. • Upon the completion of the surface cleaning, MegaFilm primer should be applied in a single coat with a brush and be left to dry for 1 to 2 hours in order to enhance the bonding strength and stabilize the surface absorption. • Gas concrete surfaces should, prior to the application of the product, be applied MegaFilm primer and the water absorption of the surfaces should so be reduced. • Exposed concrete surfaces should be applied MegaFilm BB exposed concrete primer in single coat and be left to dry for minimum 3 hours prior to the application of the adhesive mortar in order to enhance the adhesion strength. Application Methods • The product should be applied with a steel trowel, whereupon the surface should be smoothened with a gauge stick. • The application thickness should range between 2 mm and 7 mm. • Once plaster dewaters and is sufficiently hardened following the application, the surface should be processed with a trowel and final finishing touches should be made with a moist sponge. Application Recommendations • The surface should be moisturized intermittently for a period 7 days following the application in order to enhance the endurance of the plaster. • Plaster profiles should be employed on the corners in order to ensure a better quality result and high level of efficiency. • The product should not be applied to such surfaces, to which paint, premixed colorful plaster, base coat plaster or exterior coating, and to gypsum surfaces. • The product should, once mixed, be used before the expiration of its pot life. Any product, the pot life of which has expired, should not be used during the application. • Any such foreign substance as lime, cement or plaster should not be added to the mortar prepared. • Any extra water should not be added to the mixture. • The product should not be applied on unsound surfaces. The soundness and the load bearing capacity of old surfaces should be checked prior to adhesion. • The surface should be preserved from air currents and water contact during and after the application. • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be taken to ensure that the material is not exposed to direct sunlight in hot weather conditions, and the product should be mixed with cold water. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) Surface and Ambient Temperature The surface and ambient temperature should be between +5°C and 30°C whilst at application. Application Limits Useful time for prepared mortar - Pot life Plaster surface smoothing time Through dry time The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. APPLICATION INSTRUCTIONS Mixing Ratio The product should be mixed with water, weighing equal to 22 - 24 % of the product. (8.0 - 8.5 liters of water for a 35 kg package) Mixing Equipment • Low speed electrical mixer (400 cycles/min.) • Special tip stirring equipment Mixing Period The product should be stirred with a low speed mixer until any dry dust and globs are eliminated. The mortar should, then, be stirred once again for 1 to 2 minutes after being had settled for 3 to 4 minutes following preparation. Application Equipment • Steel trowel • Smoothing trowel Equipment Cleaning The equipment used should be cleaned with water following the application before the mortar dries. TECHNICAL PROPERTIES Chemical Structure: Cement based plaster with pearlite additive Dry Density: 1.40 ± 0.1 gr/cm 3 Mortar Density: 1.60 ± 0.1 gr/cm 3 Grain Size: ≤ 600 µm Coat Thickness: 2 - 7 mm Color: White Maximum 1 hour Minimum 30 minutes Minimum 2 days CONSUMPTION Recommended consumption amounts for application in roughly 1 mm thickness on 1 m 2 surface; - Gas concrete surface: 1.5 - 2.5 kg - Prime coated concrete surface: 2.0 - 3.0 kg - Roughcast applied surface: 2.0 - 3.0 kg. The said values may vary, depending on the surface and ambient conditions. 122
Page 1 and 2:
gb buildproject www.gbbuildproject.
Page 3 and 4:
VERY LOW EMISSION ENVIRONMENTALLY F
Page 5 and 6:
Definitions in Standards 4
Page 7 and 8:
Points To Be Considered! 6
Page 9 and 10:
ADHESIVES MegaFix MegaFix K MegaGra
Page 11 and 12:
Equipment Cleaning The equipment us
Page 13 and 14:
Mortar Density: 1.85 ± 0.05 gr/cm
Page 15 and 16:
CONSUMPTION The consumption amount
Page 17 and 18:
Application Equipment • Steel not
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Grain Size: ≤ 600 µm Color: Gray
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Temperature Resistance: -15°C to +
Page 33 and 34:
32
Page 35 and 36:
PACKAGING MegaPro Pastemix is deliv
Page 37 and 38:
Application Limits Useful time for
Page 39 and 40:
MegaThermo Adhesive Mortar For Ther
Page 41 and 42:
Page 43 and 44:
PACKAGING BRUFIX is delivered in ne
Page 45 and 46:
44
Page 47 and 48:
Consumption Amount Calculation Meth
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Consumption Amount Calculation Meth
Page 55 and 56:
RECOMMENDED MegaFuga Rustik CONSUMP
Page 57 and 58:
Application Limits Useful time for
Page 59 and 60:
Megaİzo Lastik Mono Cement Based,
Page 61 and 62:
Megaİzo Lastik 7 Polymer Emulsion
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Megaİzo Lastik 3 Hydrophobic Impre
Page 69 and 70:
Megaİzo Lastik 5 Elastomeric Polym
Page 71 and 72: Megaİzo Lastik 6 Elastomeric Polym
Page 73 and 74: Megaİzo Kristalize Cement Based, C
Page 75 and 76: Megaİzo K Polymer Modified, Rubber
Page 77 and 78: Megaİzo 2K Polymer Modified, Bitum
Page 79 and 80: Megaİzo CT2/CT3 - CT3 Plus Fibergl
Page 81 and 82: Megaİzo AR Slate Mineral Coated, A
Page 83 and 84: Megaİzo PU 7 Polyurethane Based, R
Page 85 and 86: Megaİzo PU 10 Polyurethane Based,
Page 87 and 88: Megaİzo PU 15 Polyurethane Based,
Page 89 and 90: Megaİzo PU 6 Bitumen Modified, Dou
Page 91 and 92: Megaİzo PU Mastik LM Polyurethane
Page 93 and 94: Megaİzo PU Mastik HM Polyurethane
Page 95 and 96: Megaİzo Stoper Cement Based, Insta
Page 97 and 98: Megaİzo File Reinforcement And Gla
Page 99 and 100: REPAIR MORTARS MegaTamir İ MegaTam
Page 101 and 102: MegaTamir K Cement Based Repair And
Page 103 and 104: MegaTamir K Yapısal Cement Based S
Page 105 and 106: 104
Page 107 and 108: PACKAGING MegaTamir Epo is delivere
Page 109 and 110: or toluene. The non-cured epoxy on
Page 111 and 112: FLOORING MATERIALS MegaZemin SL20 M
Page 113 and 114: MegaZemin BYS Surface Hardening Mor
Page 115 and 116: 114
Page 117 and 118: MegaSıva İ Cement Based, Manually
Page 119 and 120: MegaSıva K Cement Based, Manually
Page 121: MegaSıva Saten Cement Based, Manua
Page 125 and 126: MegaSıva Elyaflı Cement Based, Ma
Page 127 and 128: MegaSıva Elyaflı K Cement Based,
Page 129 and 130: MegaSıva Makine İç Cement Based,
Page 131 and 132: MegaSıva Makine Dıº Cement Based
Page 133 and 134: MegaSıva Makine Serpme Cement Base
Page 135 and 136: PRIMERS MegaFilm MegaFilm Eko MegaF
Page 137 and 138: MegaFilm Eko Surface Preparatory Pr
Page 139 and 140: MegaFilm BB High Performance Expose
Page 141 and 142: MegaFilm İzo PU Polyurethane Based
Page 143 and 144: MegaFilm AK Cement Based Binder Pri
Page 145 and 146: ADDITIVES & AUXILIARY MATERIALS Meg
Page 147 and 148: MegaAntiFreeze 10 Anti-Freeze Morta
Page 149 and 150: MegaClean Ready To Use Joint And Su
Page 151 and 152: 150
Page 153 and 154: 152
Page 155 and 156: Mantotherm Plaster Mortar Plaster M
Page 157 and 158: Mantotherm Dekominera - Grain Textu
Page 159 and 160: Mantotherm Dekominera - Fine Graine
Page 161 and 162: Mantotherm Acrylic Based Exterior P
Page 163 and 164: Mantotherm Acrylic Based Grained Ex
Page 165 and 166: Mantotherm Platinum Thermal Insulat
Page 167 and 168: Mantotherm Rockwool Thermal Insulat
Page 169 and 170: 168 .
Page 171 and 172: 170
Page 173 and 174:
172
Page 175 and 176:
174
Page 177 and 178:
176
Page 179 and 180:
k k k k k k 178
Page 181 and 182:
k k k k k k Megaİzo CT3 Plus Mega
Page 183 and 184:
k k k k k k k k k k k 182
Page 185 and 186:
Areas Of Use 184
Page 187 and 188:
Areas Of Use 186
Page 189 and 190:
Areas Of Use 188
Page 191 and 192:
Notes 190
Page 193:
gb buildersbase Premier Building Su
show all

CONSTRUCTION CHEMICALS

Create successful ePaper yourself

Delete template?

Save as template?