CONSTRUCTION CHEMICALS

More documents

Recommendations

Info

Megaİzo PK3/PK4 - PK3/PK4 Plus - PK3/PK4 Super Plus APP (Atactic Polypropylene) Modified, Plastomeric Bitumen, With Polyester Seal Carrier; (Megaİzo PK3/PK4, Megaİzo PK3/PK4 Plus) and SBS (Styrene-Butadiene-Styrene) Modified, Elastomeric Bitumen (Megaİzo PK3/PK4 Super Plus) Water Insulation Membrane PRODUCT DESCRIPTION Plastomeric/elastomeric bitumen water insulation membrane, coated with polyethylene film at both sides, the physical resistance of which has been increased by polyester seal. AREAS OF USE Suitable for use in foundations, bridges, viaducts, large size structures of art, tunnels, artificial ponds, water canals, waste storage areas, treatment plants and swimming pools. PRODUCT ADVANTAGES • Highly resistant to ruptures and tears. • Resistant to adverse impacts, which may arise in the soil. • Highly resistant to heavy building loads. • Megaİzo PK3 / PK4 is ideal for use in hot, temperate and moderate climate zones; Megaİzo PK3 / PK4 Plus is ideal for use in hot and cold (continental) climate zones; Megaİzo PK3 / PK4 Super Plus is ideal for use in cold climate zone • Megaİzo PK3 / PK4 is easily applicable under high temperature conditions; Megaİzo PK3 / PK4 Super Plus is easily applicable under low temperature conditions • Easily applied to such surfaces as chimney flashings and parapets. • Ensure waterproofing throughout the life cycle of the building. • Prior to the application, the consumption amount can be clearly and precisely determined. • Pose high level of resistance to ground waters, which contain hazardous chemicals such as sulfate. • Free from any hazardous materials. The products do not pose any threats to human health and the environment. • Elastic. PERFORMANCE PROPERTIES The foregoing values represent the results of the laboratory tests. The values provided as per the table may vary depending on the surface and ambient conditions. REFERENCE STANDARDS Certifications/Standards TS 11758 - 1 NEW APPLICABLE STANDARD UNIT Ministry of Public Works and Settlement Item No. Ministry of Public Works and Settlement Item No: 04.626/6A - 6F (Megaİzo PK3 / PK4) 04.626/2A - 2G (Megaİzo PK3 / PK4 Plus) 04.626/4A - 4G (Megaİzo PK3 / PK4 Super Plus) Megaİzo PK3 / PK4 QUALITY CERTIFICATES TSE (Megaİzo PK3 / PK4, Megaİzo PK3 / PK4 Plus) Conformant to TS 11758 - 1. (Megaİzo PK3 / PK4 Super Plus) CE Megaİzo PK3 / PK4 Plus Polyethylene film Polyethylene film Megaİzo PK3 / PK4 Super Plus Polyethylene film Polyethylene film Top surface coating - - Polyethylene film Bottom surface Polyethylene - - coating film Reinforcement - - Polyester Polyester Polyester Temperature resistance TS EN 1110 °C 110 120 110 Tensile strength (length/ width) TS EN 12311 - 1 N/5 cm 600/400 800/600 800/600 Elongation at break (length/ width) TS EN 12311 - 1 % 30/30 35/35 35/35 Cold bending TS EN 1109 °C - 5 (minimum) - 10 (minimum) - 20 (minimum) APPLICATION PROCEDURE Surface Preparation • The application surface should be dry, clean, sound and dust free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface. • The surface defects, which are deeper than 1 cm, should be repaired with MegaTamir İ or MegaTamir K 24 hours in advance. In the cases, where structural repair mortar should be used; MegaTamir İ Yapısal or MegaTamir K Yapısal should be preferred. • The molding oil residues on the concrete surface, if any, should be cleaned with high pressure water. The surface should, upon drying, be prepared for application with MegaFilm İzo. Application Methods • Edge and corner joints should be beveled with MegaTamir İ and MegaTamir K repair mortars in order for the maintenance of waterproofing. • The bottom surface of the cover should be molten with blowpipe flame, and should be adhered to make sure that the margin parts at joints overlap. • Margin parts should be allowed at the joint points by 10 cm on the width and by 15 cm on the length. • The membrane tiers should be formed perpendicularly in the same direction as the slope at all layers, and tusk tenon should be applied between any two tiers to ensure that the joint points do not overlap to the furthest extent possible. 79 Application Recommendations • Due care must be taken to make sure that the membrane selected is suitable for the prevailing climate conditions and the physical characteristics of the building. • Due care must be taken to make sure that all parts are adhered upon the completion of the application. • In cold weather conditions, the membrane should be kept in a warm environment prior to the application, and applied at such temperatures higher than +5°C. • The products should be applied in single coat or double coats for foundation waterproofing applications, depending on the ground water content of the soil, the prevailing geographical conditions of the region and the ground structure. • In the case of basement tanking application against pressure water, the products are, generally, recommended to be applied in double coats. • For roof insulation applications, if the slope is more than 5%, then one-coat of Megaİzo PK4, Megaİzo PK4 Plus or Megaİzo PK4 Super Plus could be applied according to the climate conditions and physical properties of the structures. • The insulation should be sandwiched between steel flanges at crossing spots, where the insulation is likely to be punctured. • Due care must be taken to ensure that the insulation material is not damaged by mechanical impacts in the cases of coating over the insulation. • The application surfaces should, with due consideration of the related details, be covered and protected with thermal insulation panels, drainage panels, geo-textile seal etc., and the application surface should never be left uncovered. • The product should not be applied on unsound surfaces. The soundness and the load-bearing capacity of old surfaces should be checked prior to adhesion. • The surface should be preserved from air currents and water contact during and after the application. • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) APPLICATION INSTRUCTIONS Application Equipment Blowpiper Trowel TECHNICAL PROPERTIES Chemical Structure: APP (atactic polypropylene) modified, plastomeric bitumen, with Polyester seal carrier; (Megaİzo PK3 / PK4, Megaİzo PK3 / PK4 Plus) and SBS (styrene -butadiene-styrene) modified, elastomeric bitumen (Megaİzo PK3 / PK4 Super Plus) water insulation membrane Thickness: 3 mm, 4 mm Roll Weight: 35 kg (3 mm), 45 kg (4 mm) Roll Dimensions (Width/Length): 10 m 2 CONSUMPTION The recommended consumption amount varies, depending on the size of the application surface. PACKAGING Megaİzo PK3, Megaİzo PK3 Plus, Megaİzo PK3 Super Plus are delivered in the form 1 meter wide and 10 meters long at total of 30 rolls on 100x120 cm sizes palette. Megaİzo PK4, Megaİzo PK4 Plus, Megaİzo PK4 Super Plus are delivered in the form 1 meter wide and 10 meters long at total of 20 rolls on 100x120 cm sizes palette. STORAGE CONDITIONS The product should be stored within non-tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment in the form of rolls, stowed upright. It should not be exposed to direct sunlight. The product should be protected from UV lights and sudden changes in temperature. The product should not be stored in overlapping position. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application.
Megaİzo AR Slate Mineral Coated, APP (Atactic Polypropylene) Modified Waterproofing Membrane With Plastometric Bitumen NEW PRODUCT DESCRIPTION Decorative waterproofing membrane, reinforced with polyester seal carrier, the top surface of which is slate mineral coated and the bottom surface of which is polyethylene film coated. AREAS OF USE Megaİzo AR is suitable for the general waterproofing of roofs and terraces. PRODUCT ADVANTAGES • Decorative. • Usable in such spaces without surface protection. • Does not necessitate roof tile application for roofing applications, and enables economically affordable and lightweight roofing. • Ideal for use in hot, temperate and moderate climate zones. • Easily applicable under high temperature conditions. • Fit for application to any surface. • Highly resistant to ruptures and tears. • Easily applicable to such surfaces as chimney flashings and parapets. • Ensures waterproofing throughout the life cycle of the building. • Prior to the application, the consumption amount can be clearly and precisely determined. • Poses high level of resistance to ground waters, which contain harmful chemicals such as sulfate. • Free from any hazardous materials. The product does not pose any threats to human health and the environment. • Elastic. PERFORMANCE PROPERTIES APPLICABLE STANDARD UNIT Megaİzo AR Top surface coating - - Slate mineral Bottom surface coating - - Polyethylene film Type of reinforcement - - Polyester Temperature resistance TS EN 1110 °C 110 Tensile strength (length/ width) TS EN 12311 - 1 N/5 cm 600/400 Elongation at break (length/ width) TS EN 12311 - 1 % 30/30 Cold bending TS EN 1109 °C - 5 (minimum) Dimensional stability TS EN 1107 - 1 % 0.6 (maximum) REFERENCE STANDARDS Certifications/Standards TS 11758 – 1 Ministry of Public Works and Settlement Item No. Ministry of Public Works and Settlement Item No.: 04.626/6E QUALITY CERTIFICATES Conformant to TS 11758 - 1. CE APPLICATION PROCEDURE Surface Preparation • The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface. • The surface defects, which are deeper than 1 cm, should be repaired with MegaTamir İ or MegaTamir K 24 hours in advance. In the cases, where structural repair mortar should be used; MegaTamir İ Yapısal or MegaTamir K Yapısal should be preferred. • The molding oil residues on the concrete surface, if any, should be cleaned with high pressure water. The surface should, upon drying, be prepared for application with MegaFilm İzo. • Due care must be taken to make sure that all parts are adhered upon the completion of the application. • In cold weather conditions, the membrane should be kept in a warm environment prior to the application, and applied at such temperatures higher than +5°C. • The product should not be applied on unsound surfaces. The soundness and the load-bearing capacity of old surfaces should be checked prior to adhesion. • The surface should be preserved from air currents and water contact during and after the application. • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) APPLICATION INSTRUCTIONS Application Equipment Blowpiper Trowel TECHNICAL PROPERTIES Chemical Structure: Slate mineral coated, APP (atactic polypropylene) modified waterproofing membrane with plastometric bitumen Thickness: 3.5±0.2 mm Roll Weight: 42±2 kg Roll Dimensions (Width/Length): 10 m 2 Color: Red, green CONSUMPTION The recommended consumption amount varies, depending on the size of the application surface. PACKAGING Megaİzo AR is delivered in the form 1 meter wide and 10 meters long at total of 20 rolls on 100x120 cm sizes palette. STORAGE CONDITIONS The product should be stored within non-tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment in the form of rolls, stowed upright. It should not be exposed to direct sunlight. The product should be protected from UV lights and sudden changes in temperature. The product should not be stored in overlapping rolls. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application. Application Methods • Edge and corner joints should be beveled with MegaTamir İ and MegaTamir K repair mortars in order for the maintenance of waterproofing. • The bottom surface of the cover should be molten with blowpipe flame, and should be adhered to make sure that the margin parts at joints overlap. • Margin parts should be allowed at the joint points by 10 cm on the width and by 15 cm on the length. • The minerals, which may have dropped on the margin parts, if any, should be cleaned. • The membrane tiers should be formed perpendicularly in the same direction as the slope at all layers, and tusk tenon should be applied between any two tiers to ensure that the joint points do not overlap to the furthest extent possible. • In the cases of longitudinal overlapping, the granules should be scraped thoroughly, be heated with blowpiper and be embedded into the membrane with a trowel. Application Recommendations • Due care must be taken to make sure that the membrane selected is suitable for the prevailing climate conditions and the physical characteristics of the building. 80
Page 1 and 2:
gb buildproject www.gbbuildproject.
Page 3 and 4:
VERY LOW EMISSION ENVIRONMENTALLY F
Page 5 and 6:
Definitions in Standards 4
Page 7 and 8:
Points To Be Considered! 6
Page 9 and 10:
ADHESIVES MegaFix MegaFix K MegaGra
Page 11 and 12:
Equipment Cleaning The equipment us
Page 13 and 14:
Mortar Density: 1.85 ± 0.05 gr/cm
Page 15 and 16:
CONSUMPTION The consumption amount
Page 17 and 18:
Application Equipment • Steel not
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Grain Size: ≤ 600 µm Color: Gray
Page 25 and 26:
Page 27 and 28:
Page 29 and 30: Equipment Cleaning The equipment us
Page 31 and 32: Temperature Resistance: -15°C to +
Page 33 and 34: 32
Page 35 and 36: PACKAGING MegaPro Pastemix is deliv
Page 37 and 38: Application Limits Useful time for
Page 39 and 40: MegaThermo Adhesive Mortar For Ther
Page 41 and 42: CONSUMPTION The consumption amount
Page 43 and 44: PACKAGING BRUFIX is delivered in ne
Page 45 and 46: 44
Page 47 and 48: Consumption Amount Calculation Meth
Page 53 and 54: Consumption Amount Calculation Meth
Page 55 and 56: RECOMMENDED MegaFuga Rustik CONSUMP
Page 57 and 58: Application Limits Useful time for
Page 59 and 60: Megaİzo Lastik Mono Cement Based,
Page 61 and 62: Megaİzo Lastik 7 Polymer Emulsion
Page 67 and 68: Megaİzo Lastik 3 Hydrophobic Impre
Page 69 and 70: Megaİzo Lastik 5 Elastomeric Polym
Page 71 and 72: Megaİzo Lastik 6 Elastomeric Polym
Page 73 and 74: Megaİzo Kristalize Cement Based, C
Page 75 and 76: Megaİzo K Polymer Modified, Rubber
Page 77 and 78: Megaİzo 2K Polymer Modified, Bitum
Page 79: Megaİzo CT2/CT3 - CT3 Plus Fibergl
Page 83 and 84: Megaİzo PU 7 Polyurethane Based, R
Page 85 and 86: Megaİzo PU 10 Polyurethane Based,
Page 87 and 88: Megaİzo PU 15 Polyurethane Based,
Page 89 and 90: Megaİzo PU 6 Bitumen Modified, Dou
Page 91 and 92: Megaİzo PU Mastik LM Polyurethane
Page 93 and 94: Megaİzo PU Mastik HM Polyurethane
Page 95 and 96: Megaİzo Stoper Cement Based, Insta
Page 97 and 98: Megaİzo File Reinforcement And Gla
Page 99 and 100: REPAIR MORTARS MegaTamir İ MegaTam
Page 101 and 102: MegaTamir K Cement Based Repair And
Page 103 and 104: MegaTamir K Yapısal Cement Based S
Page 105 and 106: 104
Page 107 and 108: PACKAGING MegaTamir Epo is delivere
Page 109 and 110: or toluene. The non-cured epoxy on
Page 111 and 112: FLOORING MATERIALS MegaZemin SL20 M
Page 113 and 114: MegaZemin BYS Surface Hardening Mor
Page 115 and 116: 114
Page 117 and 118: MegaSıva İ Cement Based, Manually
Page 119 and 120: MegaSıva K Cement Based, Manually
Page 121 and 122: MegaSıva Saten Cement Based, Manua
Page 123 and 124: MegaSıva Perlitli Cement Based, Ma
Page 125 and 126: MegaSıva Elyaflı Cement Based, Ma
Page 127 and 128: MegaSıva Elyaflı K Cement Based,
Page 129 and 130: MegaSıva Makine İç Cement Based,
Page 131 and 132:
MegaSıva Makine Dıº Cement Based
Page 133 and 134:
MegaSıva Makine Serpme Cement Base
Page 135 and 136:
PRIMERS MegaFilm MegaFilm Eko MegaF
Page 137 and 138:
MegaFilm Eko Surface Preparatory Pr
Page 139 and 140:
MegaFilm BB High Performance Expose
Page 141 and 142:
MegaFilm İzo PU Polyurethane Based
Page 143 and 144:
MegaFilm AK Cement Based Binder Pri
Page 145 and 146:
ADDITIVES & AUXILIARY MATERIALS Meg
Page 147 and 148:
MegaAntiFreeze 10 Anti-Freeze Morta
Page 149 and 150:
MegaClean Ready To Use Joint And Su
Page 151 and 152:
150
Page 153 and 154:
152
Page 155 and 156:
Mantotherm Plaster Mortar Plaster M
Page 157 and 158:
Mantotherm Dekominera - Grain Textu
Page 159 and 160:
Mantotherm Dekominera - Fine Graine
Page 161 and 162:
Mantotherm Acrylic Based Exterior P
Page 163 and 164:
Mantotherm Acrylic Based Grained Ex
Page 165 and 166:
Mantotherm Platinum Thermal Insulat
Page 167 and 168:
Mantotherm Rockwool Thermal Insulat
Page 169 and 170:
168 .
Page 171 and 172:
170
Page 173 and 174:
172
Page 175 and 176:
174
Page 177 and 178:
176
Page 179 and 180:
k k k k k k 178
Page 181 and 182:
k k k k k k Megaİzo CT3 Plus Mega
Page 183 and 184:
k k k k k k k k k k k 182
Page 185 and 186:
Areas Of Use 184
Page 187 and 188:
Areas Of Use 186
Page 189 and 190:
Areas Of Use 188
Page 191 and 192:
Notes 190
Page 193:
gb buildersbase Premier Building Su
show all

CONSTRUCTION CHEMICALS

Create successful ePaper yourself

Delete template?

Save as template?