Planning Guide AC Servomotors 1FT5 - Siemens Automation and ...

More documents

Recommendations

Info

Foreword Danger and warning information viii ! ! ! 05.03 Danger � It is not permissible to commission the equipment until it has been clearly identified that the machine, in which the described components are to be installed, is in full compliance with the specifications in Directive 98/37/EC. � Only appropriately qualified personnel may commission SIMODRIVE units and AC motors. � This personnel must take into account the technical customer documentation belonging to the product and be knowledgeable and observe the specified information and instructions on the hazard and warning labels. � When electrical equipment and motors are operated, the associated electrical circuits are at hazardous voltage levels. � When the machine or system is operated, hazardous axis movements can occur. � All of the work carried–out in the electrical machine or system must be carried–out with it in a no–voltage condition. � SIMODRIVE drive units are designed for operation on low–ohmic, grounded line supplies (TN line supplies). Warning � The successful and safe operation of this equipment and motors is dependent on proper transport, storage, installation and mounting as well as careful operator control, service and maintenance. � For special versions of the drive units and motors, information and data in the catalogs and quotations additionally apply. � In addition to the information and instructions on hazards and warnings in the technical customer documentation supplied, the applicable national, local and machine/system-specific regulations and requirements must be carefully taken into consideration. Caution � The motors can have surface temperatures of over +80� C. � This is the reason that it is not permissible that temperature–sensitive parts and components – e.g. cables or electrical components – are in contact with the motor or fastened to the motor. � When connecting and routing connecting cables, the following must be carefully observed: – they may not be damaged – they may not be strained, and – they may not be able to be touched by rotating components. © Siemens AG 2003 All rights reserved AC Servomotors 1FT5 (PFT5) – 05.03 Edition
05.03 © Siemens AG 2003 All rights reserved AC Servomotors 1FT5 (PFT5) – 05.03 Edition Foreword Caution � SIMODRIVE drive units with AC motors are subject to a voltage test, in compliance with EN 50178 as part of a routine test. While the electrical equipment of industrial machines is being subject to a voltage test in compliance with EN 60204-1, Section 19.4, all of the SIMODRIVE equipment connections must be disconnected/withdrawn in order to avoid damaging the SIMODRIVE equipment. � Motors should be connected–up according to the circuit diagram supplied. It is not permissible to directly connect the motors to the three–phase line supply. Motors will be destroyed if they are connected directly to the three–phase line supply. Note � SIMODRIVE equipment with AC motors fulfill, in the operational state and in dry operating areas, the Low–Voltage Directive 73/23/EEC. � SIMODRIVE equipment with AC motors fulfill, in the configurations which are specified in the associated EC Declaration of Conformity, the EMC Directive 89/336/EEC. ix
Page 1: Planning Guide 05/2003 Edition simo
Page 4 and 5: 3ls SIMODRIVE ® Documentation Prin
Page 6 and 7: 1 Kapitel Hotline vi If you have an
Page 10 and 11: x Foreword ESDS information and ins
Page 12 and 13: Table of Contents 1FT5 1FT5-12 Spac
Page 14 and 15: Motor Description 1.2 Order designa
Page 16 and 17: Motor Description 1.2 Order designa
Page 18 and 19: Motor Description 1.3 Technical ver
Page 24 and 25: Motor Description 1.4 Functions and
Page 30 and 31: Motor Description 1.5 Cooling 1) Po
Page 32 and 33: Motor Description 1.6 Electrical co
Page 34 and 35: Motor Description 1.7 Drive-out cou
Page 36 and 37: Technical Data and Characteristics
Page 58 and 59:
Technical Data and Characteristics
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Motor Components (Options) 3.1 Ther
Page 80 and 81:
Motor Components (Options) 3.2 Enco
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Motor Components (Options) 3.4 Work
Page 90 and 91:
Motor Components (Options) 3.5 Gear
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Dimension Drawings Short type of co
Page 98 and 99:
Dimension Drawings 2 3 4 5 6 7 8 1
Page 100 and 101:
Page 102 and 103:
2 3 4 5 6 7 8 1 Dimension Drawings
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
References /PFK7/ Planning Guide, A
Page 124 and 125:
References 1FT5/A-124 Space for you
Page 126 and 127:
Index Index-126 Space for your note
Page 129 and 130:
SIMODRIVE Advertising brochure SIMO
show all

Planning Guide AC Servomotors 1FT5 - Siemens Automation and ...

Create successful ePaper yourself

Delete template?

Save as template?