HEMPEL

More documents

Recommendations

Info

Specification sheet Hempel (Denmark) A/S Project: Area: BALLAST TANKS BELOW SAUNA AND LAUNDRY Remarks: DANA - DOKNING 2010 Obj. ref.: 7912680 The surface must be completely clean and dry with a temperature 3°C/5°F above the dew point to avoid condensation. At the freezing point be aware of ice on the surface. The specified high film thickness can best be obtained by airless spray application. If another application method is used more applications are necessary to achieve the specified dry film thickness. Curing agent 97334 is hazy. This is intended and has no influence on the performance. With this ballast tank coating system it is especially important that the specified film thickness is achieved all over and that a uniform film formation free of any pinholes and other defects is obtained for each coat applied. Stripe coating with brush before or after spray application of each coat is to be carried out on areas difficult to cover properly by spray such as edges, corners, flanges, cutouts, handwelds and other rough surfaces. IMO MSC.215(82) accepts roller application on scallops, ratholes, etc. only. If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion. In confined spaces provide adequate ventilation during application and drying. Before taking tank into use, allow paint film to dry and cure completely (including several days by strong ventilation). Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions Shade no. Volume solids % Curing agent volume 20°C 20°C point °C VOC g/ltr MAL Thinner Min. Temp. Max. RH% °C HEMPADUR QUATTRO 17634 50630 72 97334 4 : 1 2 h 4 h 27 275 4-5 08450 -10 HEMPADUR QUATTRO 17634 22090 72 97334 4 : 1 2 h 4 h 27 270 4-5 08450 -10 The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions of Clause 8 of the GENERAL CONDITIONS OF SALE, DELIVERY AND SERVICE shall apply to any and all claims arising out of or in connection with the use of the Product as recommended above, overleaf or otherwise. Hempel's PreSale System 2.6.16 (Build 673) User name: Henrik Berg Quality Code: 34-11 / 0710 <strong>HEMPEL</strong> Printed at: 21.07.2010 11:35 Department name: Sales Denmark Environment : Immersion Created/Last modified: 21.07.2010 11:29 DKHEJ0181 Page: 14
Specification sheet Hempel (Denmark) A/S Project: Area: ACCOMODATION INTERNAL AREAS, NEW STEEL Surface preparation: DANA - DOKNING 2010 Obj. ref.: 7912680 Oil and grease etc. to be removed by emulsion cleaning. Entire area to be (high pressure) fresh water cleaned in order to remove salts and other contaminants. Rusty and damaged areas to be mechanical cleaned to St 3 according to ISO 8501-1:2007. Product name (including quality number) Treated area % Shade Shade no. Film thickness Theoretical spreading Application methods (micron) rate Roller Wet Dry (sqm/ltr) Brush Spray Recommended HEMPALIN PRIMER HI-BUILD 13200 t/u White 10000 150 75 6.3 (X) X .021"-.023" 200 bar HEMPALIN ENAMEL 52140 t/u To shade 99990 75 30 15.3 (X) (X) X .018" 150 bar t/u: touch up f/c: full coat Total d.f.t. 105 X: Recommended (X): Possible Recoating intervals. Ample ventilation Hrs=Hour(s) Mth=Month(s) N/R=Not Recommended Quality no 13200 D.F.T. (micron) 75 Remarks and Product information see next page. Recoated with quality no 52140 Nozzle orifice 40°C 30°C 20°C 10°C 0°C -10°C Nozzle pressure Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Hempel's PreSale System 2.6.16 (Build 673) User name: Henrik Berg Quality Code: 34-11 / 0710 Printed at: 21.07.2010 11:35 Department name: Sales Denmark Environment : Mild Created/Last modified: 21.07.2010 11:29 DKHEJ0181 Page: 15 3 Hrs None 4 Hrs None 5 Hrs None 10 Hrs None N/R N/R N/R N/R <strong>HEMPEL</strong>
Page 1 and 2: Area: FLAT BOTTOM Surface preparati
Page 3 and 4: Area: VERTICAL BOTTOM Surface prepa
Page 5 and 6: Area: BALLAST TANKS Surface prepara
Page 7 and 8: Area: CHAIN LOCKER Surface preparat
Page 9 and 10: Area: FOREPEAK TANK Surface prepara
Page 11 and 12: Specification sheet Hempel (Denmark
Page 13: Specification sheet Hempel (Denmark
Page 17 and 18: Area: STERN Surface preparation: Sp
Page 19 and 20: Area: AFT DECK Surface preparation:
Page 21 and 22: Specification sheet Hempel (Denmark
Page 23 and 24: Area: HULL MARKING Surface preparat
Page 25 and 26: Area: CAP Surface preparation: Spec

HEMPEL

Create successful ePaper yourself

Delete template?

Save as template?