HEMPEL

More documents

Recommendations

Info

Area: AFT DECK Remarks: Specification sheet Hempel (Denmark) A/S Project: DANA - DOKNING 2010 Obj. ref.: 7912680 Area size: 300 sqm The surface must be completely clean and dry with a temperature 3°C/5°F above the dew point to avoid condensation. If a full blasting is desired, note that the primer coats are to be applied as full coats. The specified high film thickness can best be obtained by airless spray application. If another application method is used more applications are necessary to achieve the specified dry film thickness. Pit-corroded areas may call for an extra coat to fill out pittings. If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure intercoat adhesion. Before recoating after exposure in contaminated environments, clean the surface thoroughly by (high pressure) fresh water hosing and allow to dry. Product information: Mixing ratio Pot life Dry to touch Flash Application restrictions Shade no. Volume solids % Curing agent volume 20°C 20°C point °C VOC g/ltr MAL Thinner Min. Temp. Max. RH% °C HEMPEL'S ZINC PRIMER 16490 19840 33 30 min 7 590 08450 4-3 HEMPATEX HI-BUILD 46410 50630 42 4 h 24 513 08080 4-5 HEMPATEX HI-BUILD 46410 40640 43 4 h 24 507 08080 4-5 HEMPATEX ENAMEL 56360 40640 30 3 h 25 607 08080 4-3 The data, specifications, directions and recommendations (hereinafter "Information") given in this painting specification are based upon test results obtained under controlled or specifically defined conditions and said Information is correct to the best of our knowledge. The User must satisfy itself that it is appropriate to use the Product in accordance with the Information in the actual conditions under which the Product is intended to be used, and the Manufacturer and Seller do not guarantee the accuracy, completeness or appropriateness of the Information when the Product is used in those conditions. The provisions of Clause 8 of the GENERAL CONDITIONS OF SALE, DELIVERY AND SERVICE shall apply to any and all claims arising out of or in connection with the use of the Product as recommended above, overleaf or otherwise. Hempel's PreSale System 2.6.16 (Build 673) User name: Henrik Berg Quality Code: 34-11 / 0710 HEMPEL Printed at: 21.07.2010 11:35 Department name: Sales Denmark Environment : Medium Created/Last modified: 21.07.2010 11:29 DKHEJ0181 Page: 20
Specification sheet Hempel (Denmark) A/S Project: Area: CRANE FOUNDATIONS, GANTRY ETC. Surface preparation: DANA - DOKNING 2010 Oil and grease etc. to be removed by emulsion cleaning. Entire area to be (high pressure) fresh water cleaned in order to remove salts and other contaminants. When the surface is dry: Abrasive blasting to minimum Sa 2½ according to ISO 8501-1:2007 with a surface profile corresponding to Rugotest No. 3 BN 9a. Product name (including quality number) Treated area % Shade Shade no. Obj. ref.: 7912680 Area size: 150 sqm Film thickness Theoretical spreading Application methods (micron) rate Roller Wet Dry (sqm/ltr) Brush Spray Recommended HEMPEL'S ZINC PRIMER 16490 20 Metal grey 19840 100 35 9.4 (X) X .019"-.021" 200 bar HEMPATEX HI-BUILD 46410 20 Red 50630 250 100 4.2 (X) (X) X .017"-.021" 175 bar HEMPATEX HI-BUILD 46410 20 Grey 12170 250 100 4.2 (X) (X) X .017"-.021" 175 bar HEMPATEX ENAMEL 56360 f/c Grey 12170 100 35 9.1 (X) (X) X .017" 150 bar t/u: touch up f/c: full coat Total d.f.t. 270 X: Recommended (X): Possible Recoating intervals. Ample ventilation Hrs=Hour(s) Mth=Month(s) N/R=Not Recommended Quality no 16490 46410 46410 D.F.T. (micron) 35 100 100 Remarks and Product information see next page. Recoated with quality no 46410 46410 56360 Nozzle orifice 40°C 30°C 20°C 10°C 0°C -10°C Nozzle pressure Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. 15 Min None 25 Min None 30 Min None 55 Min None 90 Min None 3 Hrs None 2 Hrs None 3 Hrs None 4 Hrs None 7 Hrs None 12 Hrs None 26 Hrs None 3 Hrs None 4 Hrs None 5 Hrs None 10 Hrs None 16 Hrs None 35 Hrs None Hempel's PreSale System 2.6.16 (Build 673) User name: Henrik Berg Quality Code: 34-11 / 0710 Printed at: 21.07.2010 11:35 Department name: Sales Denmark Environment : Medium Created/Last modified: 21.07.2010 11:29 DKHEJ0181 Page: 21 HEMPEL
Page 1 and 2: Area: FLAT BOTTOM Surface preparati
Page 3 and 4: Area: VERTICAL BOTTOM Surface prepa
Page 5 and 6: Area: BALLAST TANKS Surface prepara
Page 7 and 8: Area: CHAIN LOCKER Surface preparat
Page 9 and 10: Area: FOREPEAK TANK Surface prepara
Page 11 and 12: Specification sheet Hempel (Denmark
Page 17 and 18: Area: STERN Surface preparation: Sp
Page 19: Area: AFT DECK Surface preparation:
Page 23 and 24: Area: HULL MARKING Surface preparat
Page 25 and 26: Area: CAP Surface preparation: Spec

HEMPEL

Create successful ePaper yourself

Delete template?

Save as template?