GeoVision V8.5 Installation Guide - XTECHCAM

More documents

Recommendations

Info

Connecting One GV-4008A Card 16 • Connect the video and audio cables to the GV-4008A Card. • Connect the supplied Hardware Watchdog Jump Wire (Figure 1-10). • Connect the computer’s internal power supply to the GV-4008A Card. The LEDs (D17, D19, D21, D23) should be lit in green to indicate the card is ready for use. Note: Figure 1-8 1. The GV-4008A Card only works when the supplied USB Dongle is inserted to PC. 2. The GV-4008A Card cannot work with microphones which acquire power from the PC. Use microphones which have external power supply.
Connecting Two GV-4008A Cards 1 Video Capture Cards You can install two GV-4008A Cards for a total of 16 channels. Master Card is the card with 1-8 channels and Slave Card is that with 9-16 channels. Normally, the card attached to the lower PCI-E slot number will act as Master, and the card attached to the higher PCI-E slot number will act as Slave. • Hardware Watchdog Connection: Connect the supplied Hardware Watchdog Jump Wire to the Master Card only (Figure 1-10). • Accessory Card Connections: � GV-Loop Through Card: Connect the card to two 10-pin connectors on each Master and Slave Card by using a supplied cable with four 10-pin headers. � GV-Multi Quad Card: Connect the card to two 10-pin connectors on each Master and Slave Card by using a supplied cable with four 10-pin headers. Figure 1-9 17
Page 1 and 2: Before attempting to connect or ope
Page 3 and 4: Contents Important Notice for V8.5.
Page 5 and 6: Important Notice for V8.5 GPU Decod
Page 7 and 8: Frame rate limit in a single hard d
Page 9 and 10: Chapter 1 Video Capture Cards This
Page 11 and 12: Connecting One GV-4008 Card • Con
Page 13 and 14: Connecting Hardware Watchdog 1 Vide
Page 15 and 16: Troubleshooting Power Supply Issues
Page 17 and 18: 1 Video Capture Cards 8. To access
Page 19: 1.2 GV-4008A 1 Video Capture Cards
Page 23 and 24: Installing Drivers 1 Video Capture
Page 25 and 26: 1.3 GV-3008 1 Video Capture Cards T
Page 27 and 28: Connecting Two GV-3008 Cards 1 Vide
Page 31 and 32: Specifications Interface PCI-E x1 G
Page 33 and 34: Packing List (D-Type) 1. GV-Combo A
Page 35 and 36: Connecting One GV-Combo A Card (DVI
Page 37 and 38: Connecting Two GV-Combo A Cards 1 V
Page 41 and 42: Interface Type PCI-E x1 Input Type
Page 43 and 44: Connecting One GV-1008 Card 1 Video
Page 45 and 46: Figure 1-20 1 Video Capture Cards A
Page 49 and 50: 1.6 GV-900A 1 Video Capture Cards O
Page 51 and 52: Connecting Two GV-900A Cards 1 Vide
Page 55 and 56: 1.7 GV-650A, GV-800A 1 Video Captur
Page 57 and 58: 1 Video Capture Cards For the BNC-t
Page 61 and 62: Specifications Interface PCI, PCI-E
Page 63 and 64: 1.8 GV-600A 1 Video Capture Cards T
Page 65 and 66: 1 Video Capture Cards For the BNC-T
Page 69 and 70: Specifications Interface PCI Input
Page 71 and 72:
Packing List 1. GV-600B, GV-650B or
Page 73 and 74:
Connecting Hardware Watchdog 1 Vide
Page 75 and 76:
Specifications Interface PCI, PCI-E
Page 77 and 78:
1.10 Installing Two Cards 1 Video C
Page 79 and 80:
1.11 Installing Drivers 1 Video Cap
Page 81 and 82:
1 Video Capture Cards GV-4008 GV-40
Page 83 and 84:
1 Video Capture Cards 1.13 Comparis
Page 85 and 86:
1 Video Capture Cards GV-1008 GV-11
Page 87 and 88:
1 Video Capture Cards GV-600B x 2 G
Page 89 and 90:
Chapter 2 Hardware Accessories This
Page 91 and 92:
Connections 2 Hardware Accessories
Page 93 and 94:
Installing Drivers 2 Hardware Acces
Page 95 and 96:
Page 97 and 98:
2.3 GV-NET Card V3.1 2 Hardware Acc
Page 99 and 100:
2 Hardware Accessories 3. You can c
Page 101 and 102:
Overview Relay Out 1 Relay Out 2 Re
Page 103 and 104:
Connections with Two Video Capture
Page 105 and 106:
Connections In I/O Box Mode 2 Hardw
Page 107 and 108:
Switching Modes 2 Hardware Accessor
Page 109 and 110:
Specifications OS Supported Input O
Page 111 and 112:
Connections Following provides two
Page 113 and 114:
Specifications OS Supported Serial
Page 115 and 116:
Extending Transmission over the Dis
Page 117 and 118:
2.7 GV-I/O 12-In Card V3 2 Hardware
Page 119 and 120:
Note: 2 Hardware Accessories 1. Use
Page 121 and 122:
Page 123 and 124:
2.9 GV-I/O Box (16 Ports) 2 Hardwar
Page 125 and 126:
Connections to PC There are three w
Page 127 and 128:
Page 129 and 130:
Specifications Input Output Input 1
Page 131 and 132:
Overview DIP Switch Figure 2-37 2 H
Page 133 and 134:
Assigning Addresses to GV-I/O Box 8
Page 135 and 136:
2 Hardware Accessories 3. Multiple
Page 137 and 138:
2.11 GV-I/O Box (4 Ports) 2 Hardwar
Page 139 and 140:
Connections to PC There are two way
Page 141 and 142:
Page 143 and 144:
2 Hardware Accessories 2.12 Accessi
Page 145 and 146:
2.12.2 DHCP Connection 2 Hardware A
Page 147 and 148:
2.12.2.2 Configuring GV-I/O Box on
Page 149 and 150:
2.12.4 Input Setting In the left me
Page 151 and 152:
2.12.6 In/Out Monitor In the left m
Page 153 and 154:
2.12.8 Changing Login ID and Passwo
Page 155 and 156:
Chapter 3 Software Installation Thi
Page 157 and 158:
3.2 Installing the System 3 Softwar
Page 159 and 160:
3.3 Program List The Surveillance S
Page 161 and 162:
Chapter 4 Screen Overview This chap
Page 163 and 164:
The controls in the main screen: No
Page 165 and 166:
The controls in the ViewLog window:
Page 167 and 168:
4.3 SingleView Viewer 16 15 14 13 1
Page 169 and 170:
The controls in the MultiView Viewe
Page 171 and 172:
The controls in the Center V2 windo
Page 173 and 174:
Troubleshooting
Page 175 and 176:
Troubleshooting A message “Can’
show all

GeoVision V8.5 Installation Guide - XTECHCAM

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?