Manual - Surveillance System, Security Cameras, and CCTV ...

More documents

Recommendations

Info

82 1.10.2 Setting Alert Notification 1. Click the Configure button (No.14, Figure 1-2), select General Setting, and select System Configure. The System Configure dialog box appears. 2. To change the default alert method, click the Arrow button in the Send Alerts Approach section, and select Hotline. Figure 1-65 3. To define the alert event, select Send Event Alerts in the Monitor Option section, click the Arrow button and select the events for which hotline alerts will be sent (Figure 1-3). Figure 1-66 4. To send hotline alerts when motion is detected, click the Camera Record Setting tab on the System Configure dialog box and select Invoke to Send Alerts. You can select specific cameras for this application or click the Finger button to apply the setting to all the cameras. Figure 1-67
5. Start monitoring. When the specified events or motion is detected, hotline alerts will be sent out automatically. 1 Configuring Main System For related settings, see Send Alert Approach, Invoke to Send Alerts and Send Event Alerts earlier this chapter. 83
Page 1 and 2:
Multicam Digital Surveillance Syste
Page 3 and 4:
Full Manual for V8.4 GeoVision Surv
Page 5 and 6:
iv 1.5.5 Setting Double Password fo
Page 7 and 8:
vi 3.3.2 Tracking in PIP View......
Page 9 and 10:
viii 4.12 Specifications ..........
Page 11 and 12:
x 8.2.3 Video Settings ............
Page 13 and 14:
xii 9.4.4 Viewing Host Information
Page 15 and 16:
xiv 11.9.6 Retrieving Recorded File
Page 17 and 18:
Chapter 1 Configuring Main System .
Page 19 and 20:
1.16 Picture-and-Picture View .....
Page 21 and 22:
Allow removing password System: It
Page 23 and 24:
11 Network Enables the connection t
Page 25 and 26:
1.1.3 Playing Back Video You can in
Page 27 and 28:
1.2.1 Configuring Global Recording
Page 29 and 30:
4. To switch between the mini and n
Page 31 and 32:
Pre-recording duration = Total Fram
Page 33 and 34:
1.2.2 Setting Data Storage You can
Page 35 and 36:
Note: 1 Configuring Main System 1.
Page 37 and 38:
Resolution Button: This button is o
Page 39 and 40:
Output Module: Triggers the specifi
Page 41 and 42:
1.2.5 Geo Mpeg4 Advanced Settings 1
Page 43 and 44:
1.2.6 Selecting Screen Layout This
Page 45 and 46:
1.2.8 Installing Cameras and Audios
Page 47 and 48: 1.2.10 Setting Text Overlay You can
Page 49 and 50: 1.3.2 Fixing Aspect Ratio This feat
Page 51 and 52: In the Auto Gain Control window, cl
Page 53 and 54: 1 Configuring Main System [WebCam,
Page 55 and 56: 1.3.5 Hard Disk Calculator 1 Config
Page 57 and 58: 1.3.6 Turbo Mode Turbo mode allows
Page 59 and 60: 1.4 Camera Monitoring Click the Mon
Page 61 and 62: 1.4.3 Daylight Saving Time Recordin
Page 63 and 64: 1.5 Account and Password The passwo
Page 65 and 66: Force Password change at the first
Page 67 and 68: 1.5.3 Retrieving Password Through E
Page 69 and 70: 1.5.5 Setting Double Password for V
Page 71 and 72: 1.6.2 Auto Login User without Acces
Page 73 and 74: 1.7 System Log System Log provides
Page 75 and 76: IO Monitor Start / Stop: Appears wh
Page 77 and 78: [POS] This function shows the POS e
Page 79 and 80: [Default Video Player] Monitor Tab
Page 81 and 82: 1.8 Recording Schedule You can prog
Page 83 and 84: 1.8.2 Special Days Schedule 1. Clic
Page 85 and 86: 1.8.4 Center V2 Schedule 1 Configur
Page 87 and 88: 2. Click Add schedule. This dialog
Page 89 and 90: Viewing Compacted Video Files After
Page 91 and 92: 3. In the Task Name field, name the
Page 93 and 94: 1.9.3 Setting Backup Schedule You c
Page 95 and 96: 1.10 Hotline Notification When even
Page 97: d. Select PCM 8,000 Hz, 8-bit Mono,
Page 101 and 102: E-Mail To: Type recipients’ e-mai
Page 103 and 104: 1.12 PTZ Control 1 Configuring Main
Page 105 and 106: 1.12.1 Mapping PTZ Cameras This opt
Page 107 and 108: 1. Select Tour Schedule on the Came
Page 109 and 110: 1.12.4 PTZ Automation Other than th
Page 111 and 112: 1.14 Video Noise Solutions The syst
Page 113 and 114: 1.14.2 Noise Detection to Reduce Fi
Page 115 and 116: 1.15 Picture-in-Picture View With t
Page 117 and 118: 1.17 Fisheye View A fisheye camera
Page 119 and 120: Setting up a Third-Party Fisheye Ca
Page 121 and 122: 1.18 Shortcuts You can create up to
Page 123 and 124: 1.19.2 Touch Screen Panel The touch
Page 125 and 126: 1.20 System Tools 1.20.1 Colorful M
Page 127 and 128: 1.20.2 Image Quality of DirectDraw
Page 129 and 130: 1.20.4 Deactivating Video Lost Beep
Page 131 and 132: 1.20.6 Fast Key Reference This opti
Page 133 and 134: 1.20.8 Version Information To know
Page 135 and 136: Hybrid and NVR Solution To implemen
Page 137 and 138: 2.3 Hybrid Solution Description 2 H
Page 139 and 140: 2.5 IP Channel Setup The setup proc
Page 141 and 142: 6. Click Apply. The IP camera is ad
Page 143 and 144: 2 Hybrid and NVR Solution [Image Or
Page 145 and 146: 2.7 RTSP Connection You can add an
Page 147 and 148: 2.8 ONVIF & PSIA Connection The GV-
Page 149 and 150:
5. Repeat steps 3 and 4 to map more
Page 151 and 152:
5. Under the Economic Frame Rate Se
Page 153 and 154:
2.11 On Demand Display 2 Hybrid and
Page 155 and 156:
Chapter 3 Video Analysis...........
Page 157 and 158:
Video Analysis 3.1 Object Tracking
Page 159 and 160:
[Setup] Pan, Tilt and Zoom: Use th
Page 161 and 162:
Starting Object Tracking After the
Page 163 and 164:
3.1.2 Object Zooming If only one PT
Page 165 and 166:
Starting Object Zooming After the a
Page 167 and 168:
Setting up Advanced Single Camera T
Page 169 and 170:
3.3 Digital Object Tracking Without
Page 171 and 172:
3.3.2 Tracking in PIP View The PIP
Page 173 and 174:
3.4 Object Counting and Intrusion A
Page 175 and 176:
3. To test your counting settings,
Page 177 and 178:
6. To activate the function at cert
Page 179 and 180:
4. Select one camera from the drop-
Page 181 and 182:
3.5.3 Searching Object Index You ca
Page 183 and 184:
3.6 Automatic Video Snapshots The V
Page 185 and 186:
3.6.2 Searching Video Snapshots You
Page 187 and 188:
3.7 Face Detection The Face Detecti
Page 189 and 190:
3.8.2 Setting Face Count 1. Click t
Page 191 and 192:
Output Module: Activates the output
Page 193 and 194:
Figure 3-32 Object Monitor 5. In th
Page 195 and 196:
Other Controls in the Video Object
Page 197 and 198:
3.10 Privacy Mask Protection The Pr
Page 199 and 200:
3.11 Scene Change Detection The Sce
Page 201 and 202:
3.12 Panorama View Spliced from mul
Page 203 and 204:
3. From the Reference drop-down lis
Page 205 and 206:
3.13 Video Defogging Smoky environm
Page 207 and 208:
3.15 Advanced Motion Detection To a
Page 209 and 210:
3.16 Crowd Detection Crowd detectio
Page 211 and 212:
Note: For the Skip Instant Light Ch
Page 213 and 214:
Tolerance Time of Alarm: Sets the d
Page 215 and 216:
3.18 Advanced Unattended Object Det
Page 217 and 218:
14. Start monitoring to run the app
Page 219 and 220:
5. Select Sensitivity. The higher t
Page 221 and 222:
3.20 Video Analysis Schedule A sche
Page 223 and 224:
3.21 Specifications Feature Notes P
Page 225 and 226:
Chapter 4 Video Playback ..........
Page 227 and 228:
Video Playback Recorded files can b
Page 229 and 230:
The controls in the ViewLog window:
Page 231 and 232:
4.1.1 Playback Screen Layout 4 Play
Page 233 and 234:
4.1.2 Playback Control Buttons Vide
Page 235 and 236:
4.1.3 Bookmarking a Frame 4 Playing
Page 237 and 238:
4.1.4 Searching a Video Event 4 Pla
Page 239 and 240:
List Mode and Line Mode 4 Playing B
Page 241 and 242:
Setting up the MDB filter: 1. Click
Page 243 and 244:
5. If the video event has the Priva
Page 245 and 246:
[Set Location] Click the […] butt
Page 247 and 248:
4.1.7 Saving Images You can save th
Page 249 and 250:
4.1.9 Recycling Option for Video Fi
Page 251 and 252:
4 Playing Back Video Files [Multi V
Page 253 and 254:
[Play Setting] Figure 4-23 [General
Page 255 and 256:
4 Playing Back Video Files Using C
Page 257 and 258:
4.2 Object Search 4 Playing Back Vi
Page 259 and 260:
4.3 Advanced Log Browser 4 Playing
Page 261 and 262:
4.3.1 Filter Settings You can defin
Page 263 and 264:
4.4 Quick Search Quick Search is a
Page 265 and 266:
4.4.1 Event Query Settings Click th
Page 267 and 268:
4.5 Address Book With Address Book,
Page 269 and 270:
4.5.3 Creating a Folder Link 4 Play
Page 271 and 272:
4.5.5 Importing and Exporting the A
Page 273 and 274:
2. Click the Add button to bring up
Page 275 and 276:
4.7.2 Retrieving Recordings from Mu
Page 277 and 278:
4.7.4 Resuming Backup 4 Playing Bac
Page 279 and 280:
To stop a connection, click the End
Page 281 and 282:
4.8.2 Running Remote Playback Clien
Page 283 and 284:
Disconnecting from RPB Server Click
Page 285 and 286:
[Connection List] Indicates the num
Page 287 and 288:
Preference Settings Figure 4-52 4 P
Page 289 and 290:
4 Playing Back Video Files 7. Selec
Page 291 and 292:
4.11 Fast Key Reference 4 Playing B
Page 293 and 294:
Backup, Deletion and Repair CHAPTER
Page 295 and 296:
5.2 Backing Up Recorded Files Using
Page 297 and 298:
[Information] Database Files: Clic
Page 299 and 300:
5 Backup, Deletion and Repair 2. Fo
Page 301 and 302:
5.4 Deleting Recorded Files To dele
Page 303 and 304:
5.5 Repairing Damaged File Paths 5
Page 305 and 306:
5.6 Repairing Damaged Video Files 5
Page 307 and 308:
Chapter 6 I/O Applications.........
Page 309 and 310:
6.1 I/O Device Setup To connect the
Page 311 and 312:
Output Module: Triggers the specifi
Page 313 and 314:
Following illustrations can help yo
Page 315 and 316:
2. Input (N/O + Latch Trigger) + Ou
Page 317 and 318:
6.3 Advanced I/O Applications In th
Page 319 and 320:
6.3.2 Setting Momentary and Maintai
Page 321 and 322:
6.3.4 Overlaying Input Name onto Sc
Page 323 and 324:
6.4 Input State Detection This feat
Page 325 and 326:
6.6 Advanced I/O Panel The Advanced
Page 327 and 328:
Editing a Group: To modify group se
Page 329 and 330:
6.6.3 Configuring the Advanced I/O
Page 331 and 332:
Creating a Mode Schedule: Define th
Page 333 and 334:
6.6.6 Forcing Output To manually fo
Page 335 and 336:
6.6.8 System-Wide Triggers The Syst
Page 337 and 338:
6.6.10 Managing a Group of I/O Devi
Page 339 and 340:
6.7.2 Using Visual Automation 1. On
Page 341 and 342:
6.8.1 Setting Up a Module Up to 16
Page 343 and 344:
Point-Of-Sale (POS) Application CHA
Page 345 and 346:
Settings At the POS device: 7 Point
Page 347 and 348:
7.1.2 Data Capture Box Integration
Page 349 and 350:
5. Select POS Data Sender from Wind
Page 351 and 352:
8. Click Start Service to send grap
Page 353 and 354:
7 Point-of-Sale (POS) Application
Page 355 and 356:
7 Point-of-Sale (POS) Application
Page 357 and 358:
7 Point-of-Sale (POS) Application [
Page 359 and 360:
7.6.1 Setting Alarm Frequency To el
Page 361 and 362:
7.7 Codepage Mapping 7 Point-of-Sal
Page 363 and 364:
7.9 POS Live View 7 Point-of-Sale (
Page 365 and 366:
7.10 POS Color Text 7 Point-of-Sale
Page 367 and 368:
7 Point-of-Sale (POS) Application 5
Page 369 and 370:
8.6.2 Host List....................
Page 371 and 372:
8.1 Remote Viewing Using a Web Brow
Page 373 and 374:
The following WebCam server feature
Page 375 and 376:
Note: When Enhance network security
Page 377 and 378:
8.2.3 Video Settings Figure 8-6 Ma
Page 379 and 380:
8.2.5 Audio Settings Connecting Aud
Page 381 and 382:
8.2.6 JPG Settings These settings a
Page 383 and 384:
8.2.8 Mobile Settings These setting
Page 385 and 386:
8.2.10 UPnP Settings WebCam Server
Page 387 and 388:
Enabling UPnP on the WebCam Server
Page 389 and 390:
8.2.12 Network Port Information The
Page 391 and 392:
6 Change Camera Selects the desired
Page 393 and 394:
8.3.2 Server List You can add the c
Page 395 and 396:
8.3.4 Alarm Notification The Single
Page 397 and 398:
There are three options for audio q
Page 399 and 400:
8.3.7 PTZ Control Click the Camera
Page 401 and 402:
8.3.9 I/O Control The new interface
Page 403 and 404:
8.3.11 Picture-in-Picture View With
Page 405 and 406:
8.3.13 Image Enhancement To enhance
Page 407 and 408:
[Monitor] Enable I/O and Schedule m
Page 409 and 410:
8.5 Multi-Window Viewer The Multi W
Page 411 and 412:
The controls in the Multi View: Fig
Page 413 and 414:
8.6.2 Host List The Host List displ
Page 415 and 416:
8.6.4 Adding a Host The Multi View
Page 417 and 418:
5. Click the Edit tab. This dialog
Page 419 and 420:
8.6.7 Camera Polling To add cameras
Page 421 and 422:
8.6.9 PTZ Control 1. Select a PTZ c
Page 423 and 424:
8.6.11 Output Control 1. Click the
Page 425 and 426:
8.6.13 System Configuration Click t
Page 427 and 428:
8.6.14 Camera Status To show the ca
Page 429 and 430:
8.6.16 Icon Image Change The icons
Page 431 and 432:
Note: If you select different netwo
Page 433 and 434:
8.7.3 Receiving Multicast and Audio
Page 435 and 436:
8.8 JPEG Image Viewer JPEG Image Vi
Page 437 and 438:
8.10 Remote ViewLog Through WebCam
Page 439 and 440:
8. To export the search results, se
Page 441 and 442:
8.13 Mobile Phone Applications With
Page 443 and 444:
8.13.1 Windows PDA GV-GView V2 is a
Page 445 and 446:
Playing Back the Recordings To play
Page 447 and 448:
Accessing I/O Devices To access the
Page 449 and 450:
Controlling PTZ Cameras To control
Page 451 and 452:
8.13.2 Windows Smartphone With the
Page 453 and 454:
4. Once the connection is establish
Page 455 and 456:
8.13.3 Symbian Smartphone With the
Page 457 and 458:
Playing Back the Recordings To play
Page 459 and 460:
Forcing Outputs 1. To force any con
Page 461 and 462:
4. On the camera list, click the de
Page 463 and 464:
8.13.6 I-Mode Phone You can monitor
Page 465 and 466:
8.13.7 iPhone GV-iView V2.1 functio
Page 467 and 468:
Other Functions After you enlarge o
Page 469 and 470:
My Favorite On the login screen (Fi
Page 471 and 472:
8.13.8 Android Using the GV-AView V
Page 473 and 474:
6. Tap the Connection button to con
Page 475 and 476:
6. Press the menu button on the mob
Page 477 and 478:
Chapter 9 E-Map Application .......
Page 479 and 480:
9.1.1 The E-Map Editor Window 8 7 1
Page 481 and 482:
6. To change the icons for I/O devi
Page 483 and 484:
9.3 Starting E-Map After creating a
Page 485 and 486:
9.4 Starting E-Map from a Remote Si
Page 487 and 488:
9.4.2 Logging in Different Hosts Wh
Page 489 and 490:
Main System. See Pop-up Live Video
Page 491 and 492:
9.4.5 Accessing Remote ViewLog On t
Page 493 and 494:
9.5.2 The E-Map Server Window Go to
Page 495 and 496:
9.5.4 Remote Monitoring via E-Map S
Page 497 and 498:
Chapter 10 Short Message Service...
Page 499 and 500:
10.2 The SMS Server Window Run the
Page 501 and 502:
10.3.2 Server Settings 10 Short Mes
Page 503 and 504:
[Notify] Figure 10-5 Server Setting
Page 505 and 506:
Creating a client: 1. Click the Add
Page 507 and 508:
10.4.2 Viewing SMS Log Click the SM
Page 509 and 510:
10.5 Password Security To prevent u
Page 511 and 512:
Server IP: Enter the IP address of
Page 513 and 514:
10.6.3 Setting Alert Notification T
Page 515 and 516:
11.7.1 Installing the FBR Program .
Page 517 and 518:
Useful Utilities This chapter discu
Page 519 and 520:
11.1.2 Registering Domain Name with
Page 521 and 522:
11.1.3 Starting Dynamic DNS After r
Page 523 and 524:
11.1.4 Local DDNS Server The Local
Page 525 and 526:
MultiCast Mode Multicast Network is
Page 527 and 528:
11.2.2 Multicast Settings Figure 11
Page 529 and 530:
11.2.4 Starting TwinDVR 1. Run Twin
Page 531 and 532:
Starting WebCam Server at TwinDVR C
Page 533 and 534:
11.3 Watermark Viewer The GV-System
Page 535 and 536:
11.3.3 The Watermark Proof Window 1
Page 537 and 538:
4. Run DMPOS. exe. This dialog box
Page 539 and 540:
11.5.2 GV-Desktop Features The five
Page 541 and 542:
[Desktop Type] Select Windows or GV
Page 543 and 544:
11.6 Authentication Server The Auth
Page 545 and 546:
11.6.3 Creating a Client DVR You mu
Page 547 and 548:
11.6.5 Starting the Server To confi
Page 549 and 550:
11.6.6 Connecting GV-System to the
Page 551 and 552:
Note: When the disconnection icon a
Page 553 and 554:
3. Click Tools on the menu bar, and
Page 555 and 556:
11.7 Fast Backup and Restore With t
Page 557 and 558:
11.7.3 Customizing the Features Not
Page 559 and 560:
Restoring the System You can restor
Page 561 and 562:
11.8.1 The Media Man Tool Window Th
Page 563 and 564:
3 DVR Database Info Indicates the p
Page 565 and 566:
11.8.4 Removing a Disk Drive To rem
Page 567 and 568:
11.8.6 Setting Up LED Panel A LED p
Page 569 and 570:
11.9 Backup Server The Backup Serve
Page 571 and 572:
11.9.2 Enabling Backup Server Befor
Page 573 and 574:
[Server Settings] You can select th
Page 575 and 576:
11.9.4 Manually Adding Files for Ba
Page 577 and 578:
[Backup File List] This tab display
Page 579 and 580:
11.10 Backup Viewer With the Backup
Page 581 and 582:
11.10.3 Performing Queries On the i
Page 583 and 584:
Tools Text overlay’s camera name
Page 585 and 586:
11.11 Bandwidth Control Application
Page 587 and 588:
11.11.2 Allowing Remote Control at
Page 589 and 590:
11.11.4 Controlling a WebCam Server
Page 591 and 592:
11.11.6 Block List Setup Two types
Page 593 and 594:
11.12 Report Generator With the Rep
Page 595 and 596:
[Domain name from DDNS] This option
Page 597 and 598:
Save to HD: Select this option to s
Page 599 and 600:
11.12.4 E-Mail Attachment Settings
Page 601 and 602:
4. Type the IP or domain name, ID a
Page 603 and 604:
11.13 Spot Monitor Controller GV-Co
Page 605 and 606:
[Video Setting] Figure 11-77 [Spot
Page 607 and 608:
11.14 Quad Spot Monitor Controller
Page 609 and 610:
[DIV 1-16] In the TV Quad Setting w
Page 611 and 612:
11.14.3 Displaying TV Quad Panel On
Page 613 and 614:
2. Click the Display list. If you d
Page 615 and 616:
11.15.3 Setting Scanned Pages You c
Page 617 and 618:
7. Start monitoring. When motion is
Page 619 and 620:
11.15.6 Controlling Screen Display
Page 621 and 622:
3. Select the COM Port the GPS rece
Page 623 and 624:
11.16.3 Recording GPS Locations of
Page 625 and 626:
Note: 1. If you like to use the map
Page 627 and 628:
7. To create connection to other GV
Page 629 and 630:
11.17 GV-IP Device Utility The IP D
Page 631 and 632:
11.17.3 Setting up IP Devices 1. Do
Page 633 and 634:
11.18 MCamCtrl Utility The MCamCtrl
Page 635 and 636:
Troubleshooting Hardware 1. Message
Page 637 and 638:
6. Can’t invoke hotline alerts.
Page 639 and 640:
WebCam 1. A message "can't connect
Page 641 and 642:
B. Supported PTZ Protocols and Mode
Page 643 and 644:
C. Certified PTZ Models for Object
Page 645 and 646:
E. Supported IP Device Brands Appen
Page 647 and 648:
G. Custom Icon Naming Chart for Mul
show all

Manual - Surveillance System, Security Cameras, and CCTV ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?