FL900 Series Flow Logger - Hachflow

More documents

Recommendations

Info

Figure 4 External power options 1 2-conductor power cable (Figure 5) 3 SD900 power supply 2 Power adapter cable 4 Long-life battery Figure 5 2-conductor power cable wiring 1 Power—#16 AWG red 2 Common—#16 AWG black System startup Install the Flo-Ware FL900 Driver Note: During driver installation this message will appear: "The following device has not passed the Windows Logo testing to verify its compatibility with Windows. Continuing your installation of this software may impair the correct operation of your system either immediately or in the future. Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing." Hach engineers have fully tested this product and determined that it is compatible with Windows. Press the "Continue anyway" button to finish the installation. Pre-requisite: Before the FL900 logger is attached to a computer, make sure that Flo-Ware is installed on the computer. The FL900 Series Driver must be installed on the PC to communicate with the logger. 12 English
1. Find the link for the FL900 Series Driver on the Flo-Ware CD or from the website http://www.hachflow.com/p_soft_floware_down.html 2. Click on the link and run the application. The install wizard starts. 3. Follow the on-screen instructions to install the driver. Use the recommended settings. Attach the logger to the computer Pre-requisite: Make sure that the FL900 driver is installed on the computer. Connect only one logger to the computer. 1. Attach the logger to the computer. 2. When a USB cable is attached for the first time, the Found New Hardware wizard opens. Run the new hardware wizard to install the USB driver for the logger. When finished, the message “Your new hardware is installed and ready to use” is shown. In the event the wizard does not run or the install fails, contact Hach Flow Tech Support to assist with trouble shooting your specific operating system. Attach a sensor or external devices to the logger Pre-requisite: Make sure that the connection status is offline. W A R N I N G Sensor Hazardous Locations and RF Exposure Hazards. Some sensors have RF radiation exposure hazards and are used in explosive atmospheres. See sensor manual warnings and instructions before connecting a sensor to the logger. The number of sensors that can attach to the logger varies with the model of the logger. Some sensors must attach to an external module that is used as an interface between the sensor and the logger. Figure 7 shows the AV9000 Area Velocity Analyzer module on the side of the logger and the connection to a submerged area/velocity sensor. 1. If the sensor cable has connectors on both ends, attach the cable to the sensor first. 2. Attach the sensor (or module) to any SENSOR port on the logger (Figure 6 or Figure 7). Tighten the connector by hand. Note: For rain gauges, attach the sensor to the RAIN connector. 3. If the sensor uses an external module, attach the module to the logger, then attach the sensor to the module (Figure 7). 4. If the sensor cable has a desiccant hub, align the desiccant hub vertically and make sure that the air port points down (Figure 6). English 13
Page 1 and 2: DOC026.97.80015 FL900 Series Flow L
Page 3 and 4: Table of contents Specifications on
Page 5 and 6: Use of hazard information D A N G E
Page 7 and 8: Country-specific approval for Wi-Fi
Page 9 and 10: Figure 2 Connectors—side 2 1 Sens
Page 11: 3 Attach an external power supply (
Page 15 and 16: sensors. Connect the auxiliary cabl
Page 17 and 18: 1 2 3 4 English 17
Page 19 and 20: Figure 11 Serial number location N
Page 21 and 22: Figure 12 Call the server 1 Call in
Page 23 and 24: . Select the interval from the drop
Page 25 and 26: Replace the batteries Replace the b
Page 27 and 28: Table des matières Caractéristiqu
Page 29 and 30: Veuillez lire l'ensemble du manuel
Page 31 and 32: 1. Débrancher l'équipement de la
Page 33 and 34: Figure 1 Connecteurs : côté 1 1 C
Page 35 and 36: 1 2 3 Français 35
Page 37 and 38: Figure 5 Câbles d'alimentation à
Page 39 and 40: Figure 7 Raccordement d'un capteur
Page 41 and 42: Conditions préablables : assurez-v
Page 43 and 44: Configuration d'un compte GPRS bas
Page 45 and 46: 3. Cliquez sur Communications (Comm
Page 47 and 48: Création d'un programme de base po
Page 49 and 50: Suspension à un câble A V I S N'u
Page 51 and 52: • Réglez l'antenne pour augmente
Page 53 and 54: Especificación Alarmas Acciones de
Page 55 and 56: Precauciones para espacios confinad
Page 57 and 58: Módem MTSMC-C1-GP (CDMA): • FCC:
Page 59 and 60: Conexión de una fuente de alimenta
Page 61 and 62: Conexión de una fuente de alimenta
Page 63 and 64:
entre el sensor y el registrador. F
Page 65 and 66:
Figura 8 Interfaz del usuario 1 Ins
Page 67 and 68:
1 2 3 4 Español 67
Page 69 and 70:
Figura 11 Ubicación del número de
Page 71 and 72:
Figura 12 Llamada al servidor 1 Obj
Page 73 and 74:
5. Para establecer el intervalo de
Page 75 and 76:
Figura 13 Registrador colgado de un
Page 77 and 78:
• Si no se resuelve el problema,
Page 79 and 80:
Especificação Intervalos de regis
Page 81 and 82:
Definição de um espaço confinado
Page 83 and 84:
Opinião: compatível de acordo com
Page 85 and 86:
Alterações na temperatura e press
Page 87 and 88:
Figura 4 Opções de energia extern
Page 89 and 90:
Figura 6 Anexar um sensor ao logger
Page 91 and 92:
Quando o logger possui um modem, os
Page 93 and 94:
Configure uma conta baseada em mode
Page 95 and 96:
Opção GPRS Intervalo de chamada p
Page 97 and 98:
Fazer um programa básico de logger
Page 99 and 100:
O logger pode ser pendurado a parti
Page 101:
• Caso não seja possível soluci
show all

FL900 Series Flow Logger - Hachflow

Create successful ePaper yourself

Delete template?

Save as template?