FL900 Series Flow Logger - Hachflow

More documents

Recommendations

Info

Option Primary Call Interval Secondary call interval Server Verification Code Description The frequency that the logger calls the server, not to exceed the logging interval. The frequency that the logger calls the server during an alarm condition. The account number that allows a connection to the server. 4. Click WRITE TO LOGGER to save the settings. A message window is shown: Option Warning: all data will be lost. Continue? Set Logger Clock Description All data that is stored in the logger is erased when a program is written to the logger. To save the data, select No and download the data to a safe location. Select Yes to erase all data and update the logger with the new program. Synchronize to Computer Clock—the logger uses the date and time settings of the computer. Set Logger Clock—the logger uses the date and time settings that are set by the user. If the unit has a modem, the logger automatically uses the date and time settings of the server. A pop up screen will show success or failure. 5. Go to Data Log Setup tab. Select data log channels and logging intervals. 6. Click Write to Logger to save. Verify the telemetry (wireless option) The user can manually send a call to the server to make sure that the network communication is good. 1. Temporarily attach the antenna to the logger to test the antenna and the cell coverage at the site location before installation. 2. Touch the magnet to the call initiation target (Figure 12). The modem LED indicator changes to green. 3. Look at the modem LED indicator during the call (45 to 90 seconds) and wait for a change: • LED goes off—the call to the server was successful. • LED flashes red—the call to the server failed. Note: If the connection failed, refer to Troubleshooting on page 25 for more information. 20 English
Figure 12 Call the server 1 Call initiation target 2 Magnet Verify the telemetry with Flo-Ware 1. In Flo-Ware>FL900 Driver, select Diagnostics>Modem. 2. Make sure the registration status is either home or roaming. If blank or "identify" is shown, the connection has failed. 3. Adjust the antenna for optimum signal strength and quality. 4. Click Call Server to make a call to the network. A pop up screen will indicate success or failure. Troubleshooting telemetry • Make sure the SVC is correct. • Make sure the serial number is registered and active on the host server. • Make sure the modem is enabled and the Hach IP address has been correctly entered. • If the problem persists, contact technical support. Use the mobile SMS option The FL900 modem can be configured to send or receive SMS messages. Refer to the Flo-Ware documentation for configuration information. Modbus communication The Modbus protocol can be used for communication with this instrument. Attach an external network device, such as a PLC, to the RS232 interface on the instrument to read data as it is logged. Refer to the Modbus communications section of the Flo-Ware software documentation for more information. Note: Historical data cannot be read with Modbus communication. Basic setup The information in this manual can be used to make a simple program for the logger and to calibrate the sensors. Refer to the Flo-Ware documentation for advanced options. Complete the sections in the order that they are shown. English 21
Page 1 and 2: DOC026.97.80015 FL900 Series Flow L
Page 3 and 4: Table of contents Specifications on
Page 5 and 6: Use of hazard information D A N G E
Page 7 and 8: Country-specific approval for Wi-Fi
Page 9 and 10: Figure 2 Connectors—side 2 1 Sens
Page 11 and 12: 3 Attach an external power supply (
Page 13 and 14: 1. Find the link for the FL900 Seri
Page 15 and 16: sensors. Connect the auxiliary cabl
Page 17 and 18: 1 2 3 4 English 17
Page 19: Figure 11 Serial number location N
Page 23 and 24: . Select the interval from the drop
Page 25 and 26: Replace the batteries Replace the b
Page 27 and 28: Table des matières Caractéristiqu
Page 29 and 30: Veuillez lire l'ensemble du manuel
Page 31 and 32: 1. Débrancher l'équipement de la
Page 33 and 34: Figure 1 Connecteurs : côté 1 1 C
Page 35 and 36: 1 2 3 Français 35
Page 37 and 38: Figure 5 Câbles d'alimentation à
Page 39 and 40: Figure 7 Raccordement d'un capteur
Page 41 and 42: Conditions préablables : assurez-v
Page 43 and 44: Configuration d'un compte GPRS bas
Page 45 and 46: 3. Cliquez sur Communications (Comm
Page 47 and 48: Création d'un programme de base po
Page 49 and 50: Suspension à un câble A V I S N'u
Page 51 and 52: • Réglez l'antenne pour augmente
Page 53 and 54: Especificación Alarmas Acciones de
Page 55 and 56: Precauciones para espacios confinad
Page 57 and 58: Módem MTSMC-C1-GP (CDMA): • FCC:
Page 59 and 60: Conexión de una fuente de alimenta
Page 61 and 62: Conexión de una fuente de alimenta
Page 63 and 64: entre el sensor y el registrador. F
Page 65 and 66: Figura 8 Interfaz del usuario 1 Ins
Page 67 and 68: 1 2 3 4 Español 67
Page 69 and 70: Figura 11 Ubicación del número de
Page 71 and 72:
Figura 12 Llamada al servidor 1 Obj
Page 73 and 74:
5. Para establecer el intervalo de
Page 75 and 76:
Figura 13 Registrador colgado de un
Page 77 and 78:
• Si no se resuelve el problema,
Page 79 and 80:
Especificação Intervalos de regis
Page 81 and 82:
Definição de um espaço confinado
Page 83 and 84:
Opinião: compatível de acordo com
Page 85 and 86:
Alterações na temperatura e press
Page 87 and 88:
Figura 4 Opções de energia extern
Page 89 and 90:
Figura 6 Anexar um sensor ao logger
Page 91 and 92:
Quando o logger possui um modem, os
Page 93 and 94:
Configure uma conta baseada em mode
Page 95 and 96:
Opção GPRS Intervalo de chamada p
Page 97 and 98:
Fazer um programa básico de logger
Page 99 and 100:
O logger pode ser pendurado a parti
Page 101:
• Caso não seja possível soluci
show all

FL900 Series Flow Logger - Hachflow

Create successful ePaper yourself

Delete template?

Save as template?