Aufstell- und Bedienungsanleitung Pelletofen ... - Pelletshome.com

More documents

Recommendations

Info

WP01_1_2010_de_en_fr_it_V10.doc 28 / 96 By proper operation, use, good maintenance and service, you will increase the consistency in quality as well as the lifespan of your stove. You will save valuable resources as well as contribute to preservation of nature besides saving money. 2 Dimensioned Drawing, Cable Layout 1 Mains Zuleitung supply 230V AC 2 1 2 3 SS1 50 Hz SS8 3 F 1,6 A T SS7 SS6 - ws + gn Pt1000 Room Raumfühler sensor Pt1000 Auxiliary Reserve NiCrNi Flame Flammsensor Rauchgasgebläse Flue blower Transverse Querstromgebläse current blower M M PE N L PE N L 1 2 3 1 2 3 1 1 2 2 3 3 SS10 SS11 SK1 SS3 SS4 SS2 6 polig 1 2 3 ws sw rt External ext. Raumthermostat room thermostat Residual Eingang Input Signal GND +5V Hallgeber generator Schnecke Auger M PE N L 1 2 3 1 2 3 SS12 SS5 8 polig Zündung Ignition 1 2 1 2 SS9 Bedienteilanschluss Control panel connection
WP01_1_2010_de_en_fr_it_V10.doc 29 / 96 3 System Specifications Our stoves are always connected with other building-related furnishing / products and thus set certain system prerequisites for fault-free operation like all technical products. Some particularly important requirements are explicitly mentioned in what follows. This specifications sheet does not claim completeness of contents. Please observe all guidelines / specifications, as already mentioned in the introduction. Detailed planning of the heating system must be performed beforehand by a specialised company to coordinate the individual components in the system and achieve the optimal functionality of the entire system. 3.1 Minimum operation times / Integration of an external controller Pellets belong to solid fuel category that requires more time for ignition than a liquid or gaseous fuel. The ignition step needs some minutes for the first flame to appear and the complete output of the stove is not available until about 15 minutes after starting as well as termination of the pre-heating step. When the stove is switched off, it takes some minutes until all pellets are burnt up and the flame fades out. This is contrary to oil or gas-fuelled fires. Thus, a blower follow-up time (display mode “INFO”) of a few minutes is programmed in the stove. This subsequent time interval should have elapsed before the stove is restarted. A minimum operation time has to be observed while controlling the stove with an external controller. For this purpose, a follow-up time is programmed in the controller (set using the menu “INFO”). After reaching the set temperature at the controller, the stove continues to operate until the follow-up time elapses and the burn off mode begins. 3.2 Room and ambient temperatures / moisture conditions during operation All devices are exclusively designed for indoor operation at standard humidity and room temperatures from +5°C to +25°C (ambient temperatures during operation). Safety mechanisms could become active during operation at higher temperatures or certain minimum settings have to be made on the stove at lower temperatures. Note the relevant instructions for heating operation. All stoves are not protected against spray water and may not be installed in wet rooms. 3.3 Chimney connection The connection to a chimney suitable for solid fuels is obligatory. The connection component must be made of metal. Your local chimney sweep would be pleased to advise you. Multiple layouts (joint operation on a single chimney) are possible in Germany. The feed pressure (chimney draught = negative pressure) must be between 10 Pa and 14 Pa (optimum: 12 Pa). Chimney calculation must be performed prior to installation (EN 13384). Upon interruption of voltage supply, the chimney ensures the safe removal of flue gases from the stove and thus assumes a significant safety function and must be correctly dimensioned. In case of high chimney draught, we recommend the integration of a draught delimiter. 3.4 Combustion air supply Stoves work depending upon the conditions of indoor air. Sufficient combustion air supply is mandatory. Negative pressures are not permissible in the room meant for installation of the equipment. Thus, the pertinent technical rules / regulations have to be observed upon combination with systems related to indoor air (e.g. ventilation systems, range hoods, pneumatic conveyance systems, etc.).
Page 1 and 2: WP01_1_2010_de_en_fr_it_V10.doc 1 /
Page 11 and 12: WP01_1_2010_de_en_fr_it_V10.doc 11
Page 27: WP01_1_2010_de_en_fr_it_V10.doc 27
Page 79 and 80:
WP01_1_2010_de_en_fr_it_V10.doc 79
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
show all

Aufstell- und Bedienungsanleitung Pelletofen ... - Pelletshome.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?