Aufstell- und Bedienungsanleitung Pelletofen ... - Pelletshome.com

More documents

Recommendations

Info

WP01_1_2010_de_en_fr_it_V10.doc 36 / 96 IGNITION ERROR Step Description Display menu Faulty ignition is shown by the error message “E02 igni” on the display. SOLVING IGNITION ERRORS Step Description Display menu Quit error message with Press button briefly Possible reasons – error elimination: No pellets in burn pot - Error in pellet feeding - Transfer handful of pellets until the last row of holes in the burn pot. Unused pellets in burn pot - Check for contamination - Empty burn pot <strong>com</strong>pletely - Firebox temperature sensor defective or covered with soot (Call for service technician) Doors are open or glass breakage → “E03 door” - Remove pellets from the burn pot, DO NOT refill in hopper (Embers !!! – must be stored at least for 72 hours at a fire-proof location). Close doors or replace glass panel.
WP01_1_2010_de_en_fr_it_V10.doc 37 / 96 From the “Standby” mode press “Menu OK” once: Selection of the operation mode. Using ↑↓, the appropriate mode of operation could be selected and confirmed with “Menu OK”. NORMAL HEATING MODE – MANUAL Step Description Display menu After successful ignition cycle, the stove is preset in manual heating mode (e.g. “man 04”). The current output level is displayed. The following settings are possible during the heating mode: ↑↓ ± level 1-10 = 30-100% heat output. Upon adjustment of more than 1 level, the output is adapted in a continuous manner. Example ↑↑↑ NORMAL HEATING MODE – ROOM TEMPERATURE CONTROLLED Step Description Display menu The stove automatically maintains a constant room temperature and adapts to the output level (e.g. “room 56”). If the set room temperature is exceeded even in case of lower output levels, the stove works in intermittent ON/OFF operation mode. Temperature value is shown. Level 56 corresponds to approx. 21°C room temperature. Adjust the target temperature within a range of 1 to 100 using ↑↓. Raum 56 Example ↓↓↓↓ Raum 72 NORMAL HEATING MODE – TIME-CONTROLLED / MANUAL Step Description Display menu The stove heats at the preset times (max. twice a day) with a preset output (e.g. “time 07”). The stove is in “Standby” mode apart from these heating periods. During the heating mode, the following settings are possible: ↑↓ ± level 1-10 = 30-100% heat output. Upon adjustment of more than 1 level, the output is continuously adapted. Example ↓↓↓ NORMAL HEATING MODE – TIME-CONTROLLED / ROOM TEMPERATURE-CONTROLLED (with integrated temperature sensor) Step Description Display menu The stove maintains a constant temperature at the set times and automatically adapts the output level. The stove maintains the set-back temperature apart from these heating periods. Temperature value is shown. 56 corresponds to approx. 21°C room temperature. Adjust the target temperature within a range of 1 to 100 using ↑↓. Auto 56 Example ↓↓↓↓ Auto 72 NORMAL HEATING MODE – with external room thermostat Step Description Display menu The stove is operated in the manually preset heat output level according to the regulation of the external room thermostat. Adjustment of the set temperature is possible only on the external thermostat. The setting of the heat output level is done using ↑↓.
Page 1 and 2: WP01_1_2010_de_en_fr_it_V10.doc 1 /
Page 11 and 12: WP01_1_2010_de_en_fr_it_V10.doc 11
Page 35: WP01_1_2010_de_en_fr_it_V10.doc 35
Page 87 and 88:
WP01_1_2010_de_en_fr_it_V10.doc 87
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
show all

Aufstell- und Bedienungsanleitung Pelletofen ... - Pelletshome.com

Create successful ePaper yourself

Delete template?

Save as template?