Aufstell- und Bedienungsanleitung Pelletofen ... - Pelletshome.com

More documents

Recommendations

Info

WP01_1_2010_de_en_fr_it_V10.doc 34 / 96 4.6.1 Hopper feeding Open the hopper lid. Remove the stitches of the pellet sack and point the sack with the open end downwards up to the safety grid in the hopper and slowly empty its contents. Close the hopper lid after filling and always keep it closed during operation. Our tip: Pour the pellets slowly as close as possible to the hopper to prevent dust formation. Pellets could also be transferred into the hopper with a bucket or a similar container. Note: Do not throw any foreign bodies into the hopper; eventual damage will not be covered by warranty / claims under warranty. 4.6.2 Switching on the stove Upon start-up the auger is still completely empty. The first pellets do not fall into the burn pot until about 10 minutes after the stove starts and the ignition is turned off again. The same applies if the hopper was filled too late and has completely emptied. Procedure in both cases for safe ignition of the stove: • Switch on the stove using the I/O button and wait until the pre-heating program has terminated or the first pellets fall into the burn pot. • Then switch off the stove again using the I/O button and restart after 5 seconds. The preheating program elapses once again and the stove ignites as soon as the first pellets fall into the burn pot. Repeat the procedure when needed. Our tip: If the hopper has run completely empty and there are no more pellets in the auger, you could reduce the time until the pellets fall into the burn pot once again and the stove ignites by throwing a handful of pellets until the first row of holes in the burn pot. Caution: Never fill the burn pot completely, malfunction would be the consequence.
WP01_1_2010_de_en_fr_it_V10.doc 35 / 96 4.7 Control panel The stove has a digital display for the control of different functions. The functions of the buttons are described in what follows. START-UP Step Description Display menu After connecting to the power supply, the configuration menu (once) appears in the display. Set the language using ↑↓. Confirm with “Menu OK”. The current time and date have to be set. “Menu OK” (pressing briefly) changes between hours and minutes (blinks correspondingly). “Menu OK” (pressing long) changes to day. Set day using (↑↓). Confirm with “Menu OK”. If needed, set for an external room temperature sensor. Selection is possible between a room temperature sensor integrated in the stove, an external room temperature sensor and an indoor thermostat that could act as a breaker or contactor. “konf ok” appears after completion of these settings. with “Menu OK” Subsequent change: You can return to the CONFIG Menu using Power-OFF-Power-ON + “Menu OK”, and change settings. Operation hours, consumed pellet quantity and all parameters such as switching times, output levels, control type, etc. are saved. Switch on the stove Press the button for 2 seconds Switch on the stove for start-up. The ignition program starts. Appears after renewed “Menu OK” → “standby” Upon start-up the stove runs in “manual” mode in later modifications to the operation mode previously started. If the flame temperature sensor detects a considerable increase of the firebox temperature during the start phase, the stove is considered to be ignited and switches to the normal mode of operation. = output level = Temperature value (according to set operation mode)
Page 1 and 2: WP01_1_2010_de_en_fr_it_V10.doc 1 /
Page 11 and 12: WP01_1_2010_de_en_fr_it_V10.doc 11
Page 33: WP01_1_2010_de_en_fr_it_V10.doc 33
Page 85 and 86:
WP01_1_2010_de_en_fr_it_V10.doc 85
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
show all

Aufstell- und Bedienungsanleitung Pelletofen ... - Pelletshome.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?