installation an operation for sea tel model coastal 18 satellite tv ...

More documents

Recommendations

Info

Installation Coastal 18 Ku-Band TVRO 12 Remove (cut) the Tiewraps that were used to immobilize the antenna pedestal assembly for shipping. Several are used for the elevation axis, one through a p-clamp in the dish clip and one around the azimuth yoke. The Azimuth axis has one large tie around the bottom of the azimuth yoke and under the corner of the pedestal base plate. And one tie for the Polarization axis is through one hole in the feed assembly to the diagonal brace of the azimuth yoke. Assure that the antenna pedestal rotates freely in azimuth and elevation before energizing the antenna. 13 Install the radome top. Assure that all four of the mounting nuts are tightened to fully mate the lip edges of the radome top and base. Do not exceed 24 in-lb (21 kg-cm) torque [or finger tight, then about ¼ turn tighter] when tightening nuts. Install the provided white screw covers. 4.2.4. Other system cable connections 1 Connect the 8-pin screw terminal connector on the control cable to J2 on the back of the antenna control panel. Leave sufficient length on the cable connections to the antenna control panel to be able to remove it for testing or replacement. Excess control cable length below decks may be cut off and re-terminated according to the detail on the System Block Diagram, if necessary. NOTE: be sure to open the screw clamps on the orange connector 4-6 Figure 4-2 Antenna control panel connections sufficiently to allow the wire to properly enter the connector when re-terminating the connection. 2 Connect the 2-pin screw terminal connector (previously wired to 12VDC power) to J1 on the antenna control panel . 3 Mount the antenna control panel using the provided self tapping screws to secure it in desired panel location.
Coastal 18 Ku-Band TVRO Installation 4 Connect the antenna coaxes to the appropriate “LNB inputs” on the matrix switch. Connect each of the receiver coaxes to the receiver output connectors on the matrix switch. Connect each of the receiver coaxes to its respective satellite receiver “SATELLITE IN” connector. BLUE coax - Low Band Vertical GREEN coax - High Band Vertical or RHCP WHITE coax - Low Band Horizontal RED coax - High Band Horizontal or LHCP 5 Connect a TV monitor to each of the satellite receivers using Audio/Video, RF (TV OUT) or SCART connections. Refer to the instructions in the receiver manual for details. 6 Mount each of the satellite receivers, and its television monitor, as desired. 4.3. System Setup Refer to the next section of this manual to setup your system. 4-7
Page 1 and 2: Sea Tel, Inc. 4030 Nelson Avenue Co
Page 4 and 5: Revision History REV ECO# Date Desc
Page 6 and 7: Table of Contents 3.3.4. Satellite
Page 8 and 9: Table of Contents This Page Intenti
Page 10 and 11: Introduction Coastal 18 Ku-Band TVR
Page 12 and 13: Operation Coastal 18 Ku-Band TVRO 2
Page 18 and 19: Basic System Information Coastal 18
Page 24 and 25: Installation Coastal 18 Ku-Band TVR
Page 32 and 33: Setup Coastal 18 Ku-Band TVRO 5.2.2
Page 34 and 35: Setup Coastal 18 Ku-Band TVRO 4 Con
Page 40 and 41: Setup Coastal 18 Ku-Band TVRO 6 Adj
Page 42 and 43: Setup Coastal 18 Ku-Band TVRO Figur
Page 48 and 49: Maintenance Coastal 18 Ku-Band TVRO
Page 56 and 57: Coastal 18 Technical Specifications
Page 58 and 59: Coastal 18 Technical Specifications
Page 61 and 62: Coastal 18 Ku-Band TVRO Computer In
Page 63 and 64: Coastal 18 Ku-Band TVRO Computer In
Page 65 and 66: Coastal 18 Ku-Band TVRO Drawings 9.
Page 67 and 68: System Description Polang System pa
Page 69 and 70: D C B A 56 8 7 6 5 4 3 2 1 NOTES: U
Page 71 and 72: D C B A 8 7 6 5 4 3 2 1 NOTES: UNLE
Page 73 and 74: D C B A 8 7 6 5 4 3 2 1 NOTES: UNLE
Page 78:
SHIELDED CONTROL CABLE ASSEMBLY 117
show all

installation an operation for sea tel model coastal 18 satellite tv ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?