Batten luminaires - Alfred Pracht Lichttechnik GmbH

Batten luminaires
01with
reflectors
Protection Class II according to VDE 0711/EN 60598
Ingress protection IP65
Dust-proof
Jet-proof
Shock (RC) 0.63**
230V/50 Hz
Push-fit lampholder with thumb screw
for easier maintenance (lamp replacement).
40
Only operate luminaire
with lamp cover in place!
*
Herkules T8
luminaire system
for FL T8/26 mm
with push-fit lampholders,
single- and twin-lamp
148±2
Housing: Tubular housing, fully sealed, made of white, fiberglass-reinforced polyester,
essentially fully resistant against acids and alkalis.
Socket end pieces: One-piece push-fit lampholder end pieces made of PBT,
impact resistant.
Socket: Two-slot plug-in socket with silver-plated contacts.
Lamp cover: To be supplemented with accessories on page 41!
Seals: Short, age-resistant silicone seals.
Electrical components: Low loss ballast B1 starter; electronic ballast;
through-wiring max. 7 x 2.5 mm 2 .
Installation: Variable mounting points with Pracht Clip System made of stainless
steel. Suitable for ceiling, pendant and horizontal wall mounting.
Befestigungslochabstand
Variable variabel mounting points
77±1 L
Type (VDE designation) Watt Inductive Compensated Electronic ballast L Weight
Art.-No. Art.-No. Art.-No. (mm) (kg)
Individual luminaire without through-wiring
PPR DD 100/1 1 x 18 435 100 435 101 435 103 636±2 2.0
PPD DD 100/3 1 x 36 435 230 435 231 435 233 1246±2 2.5
PPR DD 100/5 1 x 58 435 360 435 361 435 363 1546±2 3.3
PPR DD 100/2 2 x 18 435 130 435 131 435 133 636±2 2.5
PPR DD 100/4 2 x 36 435 260 435 261 435 263 1246±2 3.9
PPR DD 100/6 2 x 58 435 400 435 401 435 403 1546±2 4.9
Luminaire for individual and continuous mounting with through-wiring 2 x 1.5 mm 2
PPR DD 112/1 1 x 18 436 100 436 101 436 103 636±2 2.0
PPR DD 112/3 1 x 36 436 230 436 231 436 233 1246±2 2.5
PPR DD 112/5 1 x 58 436 360 436 361 436 363 1546±2 3.3
PPR DD 112/2 2 x 18 436 130 436 131 436 133 636±2 2.8
PPR DD 112/4 2 x 36 436 260 436 261 436 263 1246±2 4.3
PPR DD 112/6 2 x 58 436 400 436 401 436 403 1546±2 5.3
Luminaire for continuous mounting with through-wiring 4 x 1.5 mm 2
PPR DD 114/1 1 x 18 437 100 437 101 437 103 636±2 2.1
PPR DD 114/3 1 x 36 437 230 437 231 437 233 1246±2 2.6
PPR DD 114/5 1 x 58 437 360 437 361 437 363 1546±2 3.4
PPR DD 114/2 2 x 18 437 130 437 131 437 133 636±2 2.9
PPR DD 114/4 2 x 36 437 260 437 261 437 263 1246±2 4.4
PPR DD 114/6 2 x 58 437 400 437 401 437 403 1546±2 5.5
Extra cost:
El. bal. Dim 1–10V (add to electronic ballast version) 685 004
El. bal. Dim Dali (add to electronic ballast version) 685 005
El. bal. Industry (add to electronic ballast version) 36/58 685 006
**Shock version 100 999
Thumb screw for push-fit lampholder (KNS) 699 444
Cond. cross-sec. 1.5 mm 2 = 10 A / 2.5 mm 2 = 16 A
Nipple coupling 4 x 1.5 mm 2 601 205
Nipple coupling 4 x 2.5 mm 2 602 205
10
Areas of application: Lift lighting, pedestrian underpasses, ramp lighting, public transport, distilleries, commercial kitchens, swimming pools.
Protective tube Ø38mm for FL T8/26 mm.
Only operate luminaire
with lamp cover in place!
*For versions with electronic ballast:
Identification
Luminaires must be operated
with covers in place!
148±2
Luminaire Jura, tubular luminaire cover Ø 90 mm
with DLL. RAL colours available at extra cost.
77±1
209±1