Sibille Fameca Electric

More documents

Recommendations

Info

I n s u l a t e d t o o l s - 1 0 0 0 V 22 Screwdrivers - Standards and advices - non resessed screwdriver head Tournevis bi-matière et injectés - Différence entre tournevis bi-matière et injectés REFERENCE SIBILLE SAFE | Contrôle TORSION | Contrôle TORSION | Contrôle FLEXION (en DaN) Tournevis bi-matière | Standards (ISO 2380-1) | Déformation / Rupture | Déformation / Rupture IS19ND-3x75 | 0.7Nm | 1 | 100 DaN IS19ND-4x100 | 2.6 Nm | 5 | 170 DaN IS19ND-5.5x125 | 5.5 Nm | 9 | 300 DaN IS19ND-6.5x150 | 9.4 Nm | 12.5 | 300 DaN IS19ND-8x175 | 11.5 Nm | 21 | 300 DaN IC19ND-PH1x80 | / | / | 250 DaN IC19ND-PH2x100 | / | / | 300 DaN IC19ND-PH3x150 | / | / | 300 DaN IP19ND-PZ1x80 | / | / | 250 DaN IP19ND-PZ2x100 | / | / | 300 DaN IP19ND-PZ3x150 | / | / | 300 DaN REFERENCE SIBILLE OUTILLAGE | Contrôle TORSION | Contrôle TORSION | Contrôle FLEXION (en DaN) Tournevis injectés | Standards (ISO 2380-1) | Déformation / Rupture | Déformation / Rupture IS18-2x70 | 0.3 Nm | 0.8 | 30 DaN IS18-3x100 | 0.7 Nm | 1 | 100 DaN IS18-4x120 | 2.6 Nm | 4.7 | 125 DaN IS18-5.5x100 | 5.5 Nm | 8 | 180 DaN IS18-5.5x150 | 5.5 Nm | 8 | 180 DaN IS18-6.5x40 | 9.4 Nm | 12.7 | Non applicable IS18-6.5x150 | 9.4 Nm | 12.7 | 200 DaN IS18-8x150 | 11.5 Nm | 21 | 230 DaN IS18-8x200 | 11.5 Nm | 21 | 230 DaN IS18-10x150 | 25.6 Nm | 29 | 260 DaN IS18-10x200 | 25.6 Nm | 29 | 260 DaN IS18-12x200 | 48 Nm | / | 280 DaN IC18 / IP18-0x75 | / | / | 125 DaN IC18 / IP18-0x150 | / | / | 125 DaN IC18 / IP18-1x100 | / | / | 150 DaN IC18 / IP18-2x125 | / | / | 150 DaN IC18 / IP18-3x150 | / | / | 200 DaN IC18 / IP18-4x200 | / | / | 240 DaN IP18-1x40 | / | / | Non applicable IP18-2x40 | / | / | Non applicable TOOLS FOR ELECTRICIANS Resessed srewdriver head To be in compliance with the equipment manufacturer that becomes narrower, our screwdrivers allow to work in difficult accesses. Resessed srewdrivers head is a <strong>Sibille</strong> Outillage worldwide exclusivity.
IS18 - Insulated screwdrivers with recessed blade for slot-headed screws Standard : EN 60900 / IEC60900 ISO 2380-1 No material thickness on the screwdriver head. Réf. | b (mm) | Blade length (mm) | Weight (g) IS18B | 6.5 | 40 | 36 IS18 02 x 70 | 2 | 70 | 16 IS18 03 x 100 | 3 | 100 | 30 IS18 04 x 120 | 4 | 120 | 52 IS18 05,5 x 100 | 5,5 | 100 | 50 IS18 05,5 x 150 | 5,5 | 150 | 72 IS18 06,5 x 150 | 6,5 | 150 | 36 IS18 08 x 150 | 8 | 150 | 92 IS18 08 x 200 | 8 | 200 | 142 IS18 10 x 150 | 10 | 150 | 166 IS18 10 x 250 | 10 | 250 | 282 IS18 12 x 200 | 12 | 200 | 318 IS19ND - Bi-component slothead screwdrivers Standard : EN 60900/IEC60900 Réf. | b (mm) | Blade length mm IS19ND 3x75 | 3 | 75 IS19ND 4x100 | 4 | 100 IS19ND 5,5x125 | 5.5 | 125 IS19ND 6,5x150 | 6.5 | 150 IS19ND 8x175 | 8 | 175 MU18 - Insulated screwstarters with magnetic head (for slotted screws) Standard : EN 60900 / IEC60900 Use : For approaching and positioning a screw, not to be used for tightening. Réf. | Total length | Total length mm MU18 03X70 | 3 | 70 MU18 06X148 | 6 | 148 MU18L 248 | 10 | 248 MS37LL - Offset screwdriver single blade lengthwise for slotted screws Standard : EN 60900 / IEC60900 ISO 2380-1 Can be used for screws with limited clearance. Réf. | b (mm) | Blade length (mm) | Weight (g) MS37LL 6 x 100 | 6 | 100 | 45 MS37LL 8 x 130 | 8 | 130 | 70 MS37LL 10 x 150 | 10 | 150 | 90 Screwdrivers - For slot headed screws - TOOLS FOR ELECTRICIANS I n s u l a t e d t o o l s - 1 0 0 0 V 23
Page 1 and 2: Sibille Fameca Electric RN7 Sud Z.I
Page 3 and 4: S t a n d a r d s a n d a d v i c e
Page 5: B y p a s s a n d a c c e s s o r i
Page 10 and 11: I n s u l a t e d t o o l s - 1 0 0
Page 66 and 67: Sibille_EN_01_TOOL_ELEC_3_063-fin.q
Page 74 and 75:
Sibille_EN_01_TOOL_ELEC_3_063-fin.q
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106:
show all

Sibille Fameca Electric

Create successful ePaper yourself

Delete template?

Save as template?