Sibille Fameca Electric

More documents

Recommendations

Info

<strong>Sibille</strong>_EN_01_TOOL_ELEC_3_063-fin.qxd:Mise en page 1 13/01/10 15:19 Page 86 B y p a s s a n d a c c e s s o r i e s 86 400 and 800A clamps for LV switch boxes - 400 and 800A clamps for LV switch boxes - SFE 3436 - 400 A CLAMP for switch box PTV 1400 In compliance with the technical data BT 922. The clamp maintains the electrical link between a switch board and the network cable provisory equipped with screw connectors. It is possible to join generator, mobile transformer, or all other electrical work. The installation of the clamp carries out by the tightening on the edge of power bars of the switch box (bars from 40 x 5 to 120 x 12). The tightening principle and the slim width allow its installation as well between the departures equipping the switch box as the top of the bars. The clamp is fully insulated and maintains the IP2X protection degree. It is equipped of one or two 400 A sockets allowing the 400 A way with a cable or 800 A with two cables in parallel. The clamp has an integrate torque limiter allowing a optimal tightening to the operator. SFE 3435 - 800 a clamp for switch box PTV 2400 In compliance with the technical data BT 922. The clamp maintains the electrical link between a switch board and the network cable provisory equipped with screw connectors. It is possible to join generator, mobile transformer, or all other electrical work. The installation of the clamp carries out by the tightening on the edge of power bars of the switch box (bars from 40 x 5 to 120 x 12). The tightening principle and the slim width allow its installation as well between the departures equipping the switch box as the top of the bars. The clamp is fully insulated and maintains the IP2X protection degree. It is equipped of one or two 400 A sockets allowing the 400 A way with a cable or 800 A with two cables in parallel. The clamp has an integrate torque limiter allowing a optimal tightening to the operator. TOOLS FOR ELECTRICIANS
<strong>Sibille</strong>_EN_01_TOOL_ELEC_3_063-fin.qxd:Mise en page 1 13/01/10 15:19 Page 87 SFE3450 - Screw on connector CV400 et CV250 In compliance with EDF Serect technical data BT 823. The connectors are fully insulated and maintain the IP2X protection degree. They are compressed at the flexible copper unipolar cable top HO7RNF. They have got a screw M12 maintaining the contact of the connector with the reception piece. The connector tightening is carried out with a torque limiter male key H6 (18 Nm). A nunloosen protective cap is supplied with each connector. - The connector CV400 associated to the cable HO7RNF 120 mm2 maintains the 400 A transit. - The connector CV800 associated to the cable HO7RNF 50 mm2 maintains the 250 A transit. The connectors are compressed in factory on the length of the requested cable by the customer. The cables are marked N, L1, L2 and L3. Shunts equipped with two screw on system connectors - 50 mm 2 We can realize other lengths on order. Contact us. Screw on M12 connector, 200 and 400A - Screw on M12 connector, 200 and 400A - Réf. | Designation SFE3450 | Flexible bypass 1 000 V length 2 m 50 mm 2 SFE3451 | Flexible bypass 1 000 V length 3 m 50 mm 2 SFE3452 | Flexible bypass 1 000 V length 5 m 50 mm 2 SFE3453 | Shunt souple 1 000 V length 10 m 50 mm 2 SFE3454 | Flexible bypass 1 000 V length 15 m 50 mm 2 SFE3455 | Flexible bypass 1 000 V length 20 m 50 mm 2 SFE3460 | Flexible bypass 1 000 V length 2 m 120 mm 2 SFE3461 | Flexible bypass 1 000 V length 3 m 120 mm 2 SFE3462 | Flexible bypass 1 000 V length 5 m 120 mm 2 SFE3463 | Flexible bypass 1 000 V length 10 m 120 mm 2 SFE3464 | Flexible bypass 1 000 V length 15 m 120 mm 2 SFE3465 | Flexible bypass 1 000 V length 20 m 120 mm 2 SFE3421 - Entrance female screw on connector M8 for bypass 35/50 mm 2 That model directly receives all the bypass 35 and 50 mm2 equipped with thread end fittings M8. SFE3430 - Screw on base 400A EV400 In compliance with EDF Serect technical data BT 823. The base is built in on a panel of the generator or mobile transformer. Its nominal intensity is 400 A. It accepts the screw on connectors CV400 and CV250. The base is fully insulated and has a protective cap. It maintains the IP2X protection degree. TOOLS FOR ELECTRICIANS B y p a s s a n d a c c e s s o r i e s 87
Page 1 and 2:
Sibille Fameca Electric RN7 Sud Z.I
Page 3 and 4:
S t a n d a r d s a n d a d v i c e
Page 5:
B y p a s s a n d a c c e s s o r i
Page 8 and 9:
Page 10 and 11:
I n s u l a t e d t o o l s - 1 0 0
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39: I n s u l a t e d t o o l s - 1 0 0
Page 66 and 67: Sibille_EN_01_TOOL_ELEC_3_063-fin.q
Page 106: Sibille_EN_01_TOOL_ELEC_3_063-fin.q
show all

Sibille Fameca Electric

Create successful ePaper yourself

Delete template?

Save as template?