Advanced Welding Processes: Technologies and Process Control

270
References
metal transfer, Proc Ann Indian Institute of Welding (Madras; Indian Institute of
Welding) pp. 893–907.
[111] Ma J, 1982 ‘Metal transfer in MIG welding’, PhD thesis, Cranfield Institute of
Technology.
[112] Norrish J and Ward B, ‘Metal transfer analysis of FCAW using an Imacon camera’,
unpublished.
[113] Norrish J and Richardson I M, 1988 ‘Metal transfer mechanisms’, Weld Metal
Fabric, 56(1).
[114] van Adrichem T J, 1969 ‘Metal transfer’, Int Inst Weld Doc, 212-171-69.
[115] Anon, 1976 ‘Classification of metal transfer’, Int Inst Weld, XII-636-76.
[116] Norrish J, 2003 ‘A review of metal transfer classification in arc welding’, IIW
Document XII-1769-03, July, IIW, Annual Assembly, Commission XII, Romania.
[117] Nunes J, 1982 MSc Thesis, Cranfield Institute of Technology.
[118] Norrish J, 1974 ‘High deposition MIG-welding with electrode negative polarity’,
Proc 3rd. Conf on Advances in Welding Processes, Cambridge: The Welding
Institute, paper 16.
[119] Stevenson A W, 1988 ‘Analysis of burn-off behaviour of flux cored arc welding’,
MSc Thesis, Cranfield Institute of Technology.
[120] Bucknall P W, 1990 ‘Influence of power source dynamics on the burn-off rate
during pulsed GMA welding’, MSc thesis, Cranfield Institute of Technology.
[121] Chang C H, 1989 ‘Investigation of arc characteristics and metal transfer for flux
cored electrode in GMA welding’, MSc thesis, Cranfield Institute of Technology.
[122] Blackman S and Norrish J, 1988 ‘Pulsed MIG welding with gas shielded flux
cored wires. Synergic MIG update’, Weld Metal Fabric, April.
[123] Boughton P and MacGregor G, 1974 ‘Control of short circuiting in MIG-welding’,
Weld Res Int, 1.4(2).
[124] Ogasawara et al., 1987 ‘A power source for gas metal arc welding with new
current waveforms’, Weld J, March, 57–63.
[125] Stava A, 1993 Low spatter welding, Weld J, 72(1).
[126] Ou Z, Wuang Y, Ushio M and Tanaka M, 1999 New concept for the characteristic
of an arc welding power source, Report II – New development of arc control
system for CO 2 welding, Trans JWRI, 28(1).
[127] Cuiuri D, Norrish J and Cook C, 2000 Droplet size regulation in the short circuit
GMAW process using a current controlled weaveform, AWS Conference, GMA
welding for the 21st Century, Orlando, Florida, December.
[128] Jingzhong W, Ddojun C, Xintao W and Jida X, 1984 Study on the dynamic
process of half-cycle pulsed wire feeding CO 2 welding, Proc. International
Conference on Quality and Reliability in Welding, 6–8 September 1984, Hangzhou,
China, XVII-1-1 to XVII-1-6.
[129] Yongui J, Ganghua Y, Xintao W and Minghong L, 1984 A new welder for CO 2
welding with pulsed wire feeding, Proc. International Conference on Quality
and Reliability in Welding, 6–8 September, Hangzhou, China, XII-3-1 to XII-3-
6.
[130] Qilong W, Shuyan Y, Zeping Z and Weiyan J, 1984 ‘Short-circuit CO 2 welding
with combined control of current wave and wire feed’, Proc International
Conference on Quality and Reliability in Welding, 6–8 September, Hangzhou,
China, ppXII-1-1 to XII-1-6.
[131] Huismann G, 2000 Direct control of the material transfer: The controlled shortcircuiting
(CSC) – MIG process, Proc. Gas Metal Arc Welding for the 21st