Product Manual (pdf) - TSI

More documents

Recommendations

Info

38 (This page intentionally left blank) Chapter 3
Chapter 4 Maintenance The SIDEPAK Personal Aerosol Monitor Model AM510 requires periodic maintenance. The most common procedures are listed below: • Charging batteries • Zeroing • Impactor maintenance • Cyclone maintenance In addition to the procedures in this chapter, TSI recommends that you return your SIDEPAK Model AM510 Personal Aerosol Monitor to the factory for annual calibration. Regular factory-authorized cleaning and recalibration helps ensure that your instrument is working properly, has the latest updates, and will provide accurate and reliable measurements. Maintaining Rechargeable Battery Packs The SIDEPAK monitors incorporate the Smart Battery Management System technology that allows for fast charging and long battery life. This system utilizes a built-in computer chip in the battery packs. The microprocessor monitors battery capacity and calculates run time information by dividing capacity of the battery (mAH) by the instantaneous current consumed by the instrument (mA). This calculation is correct for current operating conditions and can change due to current (mA) consumption or changes in battery capacity. Conventional battery controllers can only make crude estimates of battery condition based on a simple voltage measurement. TSI rechargeable battery packs use nickel-metal hydride (NiMH) cells because they provide much greater capacity than conventional nickelcadmium (NiCad) cells and do not have the "memory" problems often associated with NiCad cells. Charging a NiMH Battery Pack The power supply allows you to power the SIDEPAK monitor from an AC wall outlet, or to charge any of the TSI NiMH battery packs. Connect the power supply/charger to an AC wall outlet and plug the other end into the power port on the side of the AM510. 39
Page 1 and 2: Exposure Monitoring Model AM510 SID
Page 3 and 4: CONTENTS SAFETY INFORMATION .......
Page 5 and 6: Safety Information When operated ac
Page 7 and 8: Chapter 1 Unpacking and Parts Ident
Page 9 and 10: Item Description Part/Model Referen
Page 11 and 12: Chapter 2 Setting-Up Supplying Powe
Page 13 and 14: Place the battery pack on top of th
Page 15 and 16: Installing the AA Battery Pack Note
Page 17 and 18: ! WARNING Use of USB connection to
Page 19 and 20: 2. Press the PAGE key to access the
Page 21 and 22: 6. After the New Hardware utility h
Page 23 and 24: Chapter 3 Operation Overview The SI
Page 25 and 26: Identifying SIDEPAK AM510 Features
Page 27 and 28: Data Log The Data Log sub menu cont
Page 29 and 30: If 30 seconds elapse without a key
Page 31 and 32: Prog 1 and Prog 2 Mode Protocols Pe
Page 33 and 34: To program the above example, do th
Page 35 and 36: Setup Menu When in Survey Mode, you
Page 37 and 38: Editing the List of Log Intervals w
Page 39 and 40: currently active cal factor. The va
Page 41 and 42: 4. After entering the new Cal Facto
Page 43: operated for a minimum of 15 minute
Page 47 and 48: echargeable batteries by placing th
Page 49 and 50: 2. Use a small screwdriver to push
Page 51 and 52: The cut-off size for any cyclone is
Page 53 and 54: Chapter 5 Troubleshooting TSI recom
Page 55 and 56: Symptom Possible Cause Corrective A
Page 57 and 58: Appendix A Specifications Specifica
Page 59 and 60: Approvals: Intrinsic Safety Rating
Page 61 and 62: Appendix B Custom Calibrations In m
Page 63 and 64: Appendix C Converting Stored Data t
Page 65 and 66: Appendix D CSA Certificate of Compl
Page 67 and 68: CSA Certificate of Compliance 61
Page 69: Appendix E AM510 Quick Reference Gu

Product Manual (pdf) - TSI

Create successful ePaper yourself

Delete template?

Save as template?