HOli.. - Memorial University's Digital Archives - Memorial University ...

More documents

Recommendations

Info

The original OpenPVL code is available at http://web.mil.edulopenprop/www/Download.html. The idea of this OpenPVL SW code is usc Solidworks to instead of Rihno with the same calculation methods. Based on this, replace all ofthe "rihno" words with "Solidworks" in the original code, whieh includes: Make rihno nag-o-I changes to Makc Slidworks nag 1 in Matlab code line 727 Geometry ( ..Make rihno nag...) changl.'S to Geometry ( ..Make Solidworks nag...) in Matlab code line 730 Function I) Geometry (...Make rihno nag...) changes to Function [I Geometry (...Make Solidworks nag...) in Matlab code line 1217 Thc part ofMatlab code to generate a propeller blade in Solidworks is integrated in the Mallab code line 1514 to instead ofRihno code. The logic nowchart ofthis solidworks eode displays as below: 112
Create all of the function commands at the beginning ofthe solidworks macro Use the calculation results in the original OpenPVL and sketch the first foil section, which is located at the root ofthe blade. (gct points first and then bspline connect all ofthe points) Sketch all the other foil sections in the order of from root to tip ofthe propeller blade. Connect all the points, which are located in the leading edge line to be as a reference line for lofting future Selecting all the foil sections and the reference line to loft them to generate a propeller bladc Hide all the points and curves for nice look 113
Page 4:
A Rapid Development Process for Mar
Page 7 and 8:
Table of Contents Abstract ... Ackn
Page 9:
List ofTables Table I: Required Inp
Page 12 and 13:
Figure 46: Surface Dynamic Pressure
Page 14 and 15:
a long time to analyze, draw, fabri
Page 16 and 17:
Simulation work is now commonly don
Page 18 and 19:
Early theoretical analysis applied
Page 20 and 21:
------------------------- provides
Page 22 and 23:
As can be secn in Table I, the lift
Page 24 and 25:
propeller geometry has to be entere
Page 27:
avoid cavitation; however, it decre
Page 31:
l" ........... ,... __ .... :l ,,_
Page 34:
Table 2: Advantages and Disadvantag
Page 41 and 42:
trend for many companies to reduce
Page 43 and 44:
fluxes through a particular control
Page 45 and 46:
known as a casting, is usually ejec
Page 47 and 48:
Table 3: Prototyping Technology Mat
Page 49:
quite accuratc for a testing level.
Page 54 and 55:
For given values ofJ, Fn, Rn, En, t
Page 56:
propeller geometry for impon into t
Page 59 and 60:
Using OpenPVL_SW I a propeller desi
Page 64:
o ...n".... 'Co 'OJ • • • DC)
Page 72 and 73:
3.3 Simulations using CosmosFloWork
Page 75 and 76: simulation domain are set to 6m and
Page 79: CosmosWorks can be used to check th
Page 82: Figure 33: Dynamic Pressure Distrib
Page 88: Chapter 4 Case Study: Simulation of
Page 94 and 95: The plots of RPM and thrust from ou
Page 96 and 97: Figure 46: Surface Dynamic Pressure
Page 98: Figure 48: Deflection ofthe AUV Pro
Page 102: In this simulation, two nose cones
Page 110 and 111: Chapter 6 Propeller Fabrication by
Page 112 and 113: Figure 60: Stratasys rDM 2000 After
Page 115 and 116: Material options for Stratasys Fusi
Page 117 and 118: Chapter 7 Conclusions and Future Wo
Page 119 and 120: References III Burtner, E., 1953, "
Page 121 and 122: [20] D'Epagnier, P.K., 2005, "A Com
Page 123: Appendix 1\: The Part ofOpcnPVL_SW
Page 131: Appendix B: SolidWorks Macro lor th
Page 134: 'create loft swModcl.ClearSelcction
show all

HOli.. - Memorial University's Digital Archives - Memorial University ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?