POWER-MASTER 500 - Victor Technologies

More documents

Recommendations

Info

INTRODUCTION 2-10 MANUAL 430429-485
3.01 Location SECTION 3: INSTALLATION Adequate air circulation is needed at all times in order to assure proper operation. Provide a minimum of 12 inches (305 mm) of free airspace on all sides of the unit. Make sure that the ventilator openings are not obstructed. Ventilation air flow is from rear to side. 3.02 Voltage Changeover For proper operation and to prevent damage to the machine, the voltage changeover must be set according to the incoming AC line voltage. Remove the left side panel of the machine to gain access to the voltage changeover board. Set the links to agree with one of the four available voltage settings. (See Figures 3-1 through 3-4). The four settings are: 200 VAC 230 VAC 400 VAC 460 VAC 1. Check the name plate of the machine for proper line voltage. 2. Move the voltage links by loosening the nuts securing the links in place. For 200 and 230 VAC settings place the two links in the 200/230V positions. For 400 and 460 VAC settings place the two links directly on top of each other in the 400/460V position. See figures 3-1 through 3-4. Make sure that the connections are properly tightened. DANGER ELECTRIC SHOCK CAN KILL. Open the main wall disconnect switch or breaker, before removing any covers or access panels on the welding machine. Live voltage is still present even with the front panel control switch OFF. Wait at least three full minutes after power has been removed before removing any covers or access panels to allow adequate time for internal capacitors to discharge. MANUAL 430429-485 3-1 INSTALLATION E4 E2 E4 400 460 400 460 E2 E3 E4 200 230 E2 E1 E3 400 230 460 200 VOLT CONNECTION Figure 3-1 E1 200 230 VOLT CONNECTION 200 230 E3 E1 Figure 3-2 400 VOLT CONNECTION E4 E1 200 230 E2 200 230 E3 200 230 Figure 3-3 230 460 VOLT CONNECTION Figure 3-4 400 460 460 200 400 Art # A-04083 Art # A-04084 Art # A-04085 Art # A-04086
Page 1: POWER-MASTER 500 450 Amp Inverter W
Page 4 and 5: TABLE OF CONTENTS SECTION 1: ARC WE
Page 7 and 8: SECTION 1: ARC WELDING SAFETY INSTR
Page 9 and 10: 5. Work in a confined space only if
Page 11 and 12: WARNING STEAM AND PRESSURIZED HOT C
Page 13 and 14: 8. N’utilisez pas de câbles éle
Page 15 and 16: AVERTISSEMENT LES ETINCELLES ET LES
Page 17 and 18: DECLARATION OF CONFORMITY Manufactu
Page 19 and 20: SECTION 2: INTRODUCTION 2.01 How To
Page 21 and 22: 2.05 General The Power-Master 500 i
Page 23 and 24: 2.07 Standard Features The power so
Page 25 and 26: 6. Meter Display: The digital meter
Page 27: U) Scaled output current signal: If
Page 31 and 32: 3.05 Grounding The frame of this we
Page 33 and 34: 3.07 Configuration Settings A. Lift
Page 35 and 36: 4.01 General SECTION 4: OPERATION R
Page 37 and 38: SECTION 5: SERVICE 5.01 General Mai
Page 39 and 40: 3. Machine powers up but fans do no
Page 41 and 42: SECTION 6: PARTS LIST 6.01 Equipmen
Page 43 and 44: 6.04 Base Parts Item Qty. Descripti
Page 45 and 46: 6.06 Rear Panel Parts Item Qty. Des
Page 47 and 48: 26 25 19 9 1 18 27 7 6 11 30 24 23
Page 49 and 50: APPENDIX 1: GENERAL INFORMATION Not
Page 51 and 52: Art # A-04106 MANUAL 430429-485 A-3
Page 53 and 54: Art # A-04107 MANUAL 430429-485 A-5
Page 55: Art # A-04108 MANUAL 430429-485 A-7

POWER-MASTER 500 - Victor Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?