NC Express FPL Manual - Finn-Power International, Inc.

More documents

Recommendations

Info

The outcome of the optimized nest will have vertical scrap cuts throughout the plate 500mm apart to split skeleton into section. Selecting Post cutting will allow skeleton scrap cutting to be done after all parts are cut. Step 3: Go back to optimizer and make now also a scrap cut in Y direction for each 250mm This will be the optimized nest : 100
Step 4: Go back to Nesting and change the quantity of the nested parts to 10. And make the nesting direction in the left down corner. Step 5: Go back to Optimizer and enable the crop line (disable all scrap cutting) The outcome of the optimized plate will cut the remnant from the skeleton allowing the rest of the sheet to be used for another job. 101
Page 1 and 2:
Finn-Power International 710 Reming
Page 3 and 4:
INTRODUCTION 7 1 OVERVIEW 8 2 SETUP
Page 5 and 6:
5.3.1.6 Grid Nesting 85 5.3.1.7 Nes
Page 7 and 8:
INTRODUCTION W elcome to NC Express
Page 9 and 10:
2 SETUP OF NC EXPRESS Setup of NC E
Page 11 and 12:
The cutting mode can be : This is m
Page 13 and 14:
2.4 NCEXPRESS OPTIONS Options will
Page 15 and 16:
Basically is just used to fill in o
Page 17 and 18:
By opening the update materials dia
Page 19 and 20:
Step 2: Select ALMg3(N2-5) 2mm Step
Page 21 and 22:
Snap Function Description Current (
Page 23 and 24:
3.1.1.3 Use of construction lines C
Page 25 and 26:
3.1.1.6.1 Lines Line between 2 Poin
Page 27 and 28:
Parallel arc through a point 27
Page 29 and 30:
3.1.1.6.4 Rectangles Rectangle spec
Page 31 and 32:
Rotate selected items from defined
Page 33 and 34:
3.1.1.6.10 Modify Commands Undo the
Page 35 and 36:
In the case where a DXF file is bei
Page 37 and 38:
The duplicate lines were ignored he
Page 39 and 40:
Description of all fields on the Ne
Page 41 and 42:
Step 2: Click the Browse button nex
Page 43 and 44:
Load Parts- In the case where the P
Page 45 and 46:
4 TOOLING PARTS Once the dxf is imp
Page 47 and 48:
4.1.2 Settings 1. Go to Tooling men
Page 49 and 50: External/Internal Contour propertie
Page 51 and 52: • Lead-in settings See Lead-in se
Page 53 and 54: At the pierce point a piercing is m
Page 55 and 56: Add loops to corner Enable- Enables
Page 57 and 58: Lead-out settings When we click on
Page 59 and 60: 4.1.4 Presheared Parts Presheared r
Page 61 and 62: Microjoints are placed on a part wh
Page 63 and 64: Pierce Point If we put a value for
Page 65 and 66: 4.1.7 Autotool Example 1- General T
Page 67 and 68: 5. Go to Tooling - Autotool and go
Page 69 and 70: When we now are going to run the au
Page 71 and 72: 4.2 MANUAL TOOLING Interactive tool
Page 73 and 74: Order of cycle can be changed by se
Page 75 and 76: Create When selecting this option t
Page 77 and 78: 4.2.4.3 Tabs Tabs will give the abi
Page 79 and 80: 5 NESTING Proper nesting yields sav
Page 81 and 82: 5.1.2 Parts Database When parts are
Page 83 and 84: 5.2.1.2 Keeping old Run Folders (St
Page 85 and 86: 5.3.1.4 Nest Accuracy Adjustments m
Page 87 and 88: Modify Once the parts are in the Sc
Page 89 and 90: Modify… Highlight plate, click Mo
Page 91 and 92: 5.5 MODIFYING PART’S/TOOLING (FOR
Page 93 and 94: 5.7.2.1 Move Selected Move selected
Page 95 and 96: Step 1: Nest Drawing1.cp with a qua
Page 97 and 98: Temporary High Temperature Area - T
Page 99: Open simulator by going to Process
Page 103 and 104: 6.2.3 Exercise- Interactive Optimiz
Page 105 and 106: Step 4: Click Close and Yes to conf
Page 107 and 108: Step 4: Click Process on the Nest E
Page 109 and 110: The Parameters tab allows for editi
Page 111 and 112: 7.3 REPORTS When NC code is generat
Page 113 and 114: As you can see we can have differen
Page 115 and 116: 8.1.2 High speed cutting mode for 1
Page 117 and 118: On the path/leads tab-page we can s
Page 119 and 120: This means that we can tool parts f
Page 121 and 122: 9.2 ADDING/MODIFYING PARTS IN ORDER
Page 123 and 124: This is a scripted part: This optio
Page 125 and 126: Alu_2mm_b_small Order name: TEST
Page 127 and 128: Once the sheets are accepted the Ne
Page 129 and 130: 10.2 CREATE PART4 129
Page 131 and 132: 10.4 CREATE PART6 131
Page 133 and 134: 11.1 COMMONLINE CUTTING AT PART LEV
Page 135 and 136: Finished Part 11.1.2 Commonline Exa
Page 137 and 138: 11.1.3 Commonline Example 3 Step 1:
Page 139 and 140: After changing the nesting paramete
Page 141 and 142: Step3 : Cutting the outside contour
Page 143 and 144: Step 7: After the first part we sta
Page 145 and 146: Step3 : Common line for all parts S
Page 147 and 148: Step 3: Go now straight to optimize
Page 149 and 150: 12.2 NESTING 2 149
Page 151 and 152:
Microjoint tab Microjointing places
Page 153 and 154:
Lead-ins settings Straight Lead-in
Page 155 and 156:
Lead-outs settings L2- Lead-out len
Page 157 and 158:
Clamp informationo Locations- The c
Page 159 and 160:
Switch Up Highlight plate, click Sw
Page 161 and 162:
Scrap cut- (Skeleton cutting) Creat
Page 163:
When we want to do a sheet probing
show all

NC Express FPL Manual - Finn-Power International, Inc.

Create successful ePaper yourself

Delete template?

Save as template?