PEL-60-60-10 - Physical Instruments

More documents

Recommendations

Info

REAR PANEL CONNECTORS 1 6 7 2 8 3 5 4 FIGURE 1.4 REAR PANEL REAR PANEL FEATURES 1. AC power inlet. 2. Fuseholder. 3. External programming signal port. 4. Positive input connector. 5. Negative input connector. 6. Chassis / line ground lug screw. 7. 9-pin D-sub male connector for RS232 Interface. 8. Standard GPIB interface connector. 12 M470030-01 Rev A
EXTERNAL PROGRAMMING PORT The external programming port provides remote sense inputs, input voltage monitoring, input current monitoring, external trigger input, external trigger output, and analog programming signal. 12 11 10 9 8 7 6 5 4 3 2 1 D G N D T R I G O U T T R I G I N P O R T F A U L T N C I M O N V M O N A N A L O G A G N D - S + S Pin 1 +S Positive remote sense. Pin 2 -S Negative remote sense. Pin 3 AGND Analog Ground. Provides common (reference) connection for external programming input. When an external programming function is not used, connect this point to Analog pin 4 to prevent EMI Noise. Pin 4 ANALOG External analog programming signal. Only in CC mode middle range, the electronic load can be programmed externally by 0-10Volts DC or DC + AC voltage. When external analog programming function is not used, connect this point to AGND pin 3 to prevent EMI Noise. Pin 5 VMON Input voltage monitoring signal. Generates a 0-10Volt output signal that is linearly proportional to the electronic load’s 0 to full-scale voltage. Pin 6 IMON Input current monitoring signal. Generates a 0-10Volt output signal that is linearly proportional to the electronic load’s 0 to full-scale current. Pin 7 NC No connection Pin 8 FAULT Fault signal output. A TTL compatible signal that becomes active (high) when any of the protections are triggered. Pin 9 PORT Digital port output. (Not implemented) Pin 10 TRIGIN External trigger signal input. A TTL compatible signal is used to activate the electronic load. Trig-in is used to change to a preset mode or switch between settings in transient mode, generate a pulse in pulse mode, or trigger the stepping mode. Pin 11 TRIGOUT External trigger signal output. A TTL compatible signal that is activated via the Trig-in or GPIB command *TRG. This output follows the state of the TRIGIN input. External trigger output is used for triggering oscilloscopes, power supplies, or other electronic loads that have external trigger input Pin 12 DGND Digital Ground. Provides the common (reference) connection for Trig-in and Trig-out. 13 M470030-01 Rev A
Page 1 and 2: Operation Manual PEL-60-60-10 Progr
Page 3 and 4: About AMETEK AMETEK Programmable Po
Page 5 and 6: SAFETY SYMBOLS WARNING The WARNING
Page 7 and 8: STEPPING OPERATION SET-UP 38 STEPPI
Page 9 and 10: FRONT PANEL CONTROLS 1 2 3 Use this
Page 11: LCD STATUS ENUNCIATOR LIQUID CRYSTA
Page 15 and 16: INPUT VOLTAGE LIMIT The programming
Page 17 and 18: DIMENSIONAL DRAWINGS (1in. = 25.4mm
Page 19 and 20: INSPECTION, CLEANING, AND PACKAGING
Page 21 and 22: FUSE REPLACEMENT If the fuse is sus
Page 23 and 24: LOAD WIRING LENGTH FOR OPERATION WI
Page 25 and 26: REMOTE SENSE CONFIGURATION CAUTION
Page 27 and 28: TRIGGER OPERATION Figure 2.5 depict
Page 29 and 30: OPERATING STATUS INFORMATION All op
Page 31 and 32: MAIN LEVEL LOCAL OPERATION There ar
Page 33 and 34: B: GPIB Menu - press ENTER key: *Us
Page 35 and 36: FUNCTION MENU REFERENCE The Functio
Page 37 and 38: Press the "Utility/Local" key then
Page 39 and 40: STEP NUMBER When the stepping opera
Page 41 and 42: PRINTER ON/OFF toggles the printer
Page 43 and 44: TRANSIENT FREQUENCY, SLEW RATE AND
Page 45 and 46: STEPPING MODE In stepping mode the
Page 47 and 48: FOUR: REMOTE PROGRAMMING INTRODUCTI
Page 49 and 50: egular Electronic Load commands. Th
Page 51 and 52: CURR:PROT:UND:DEL This command sets
Page 53 and 54: RES:LIM:MIN This command sets and q
Page 55 and 56: POW:PROT:OVER This command sets a p
Page 57 and 58: MODE / MODE? ⇒Mode Selection Comm
Page 59 and 60: UTIL:EOI This command sets or queri
Page 61 and 62: PROTECTION commands OVER Voltage va
Page 63 and 64:
CALIBRATION REQUIRED EQUIPMENT •
Page 65 and 66:
CONSTANT VOLTAGE (CV) MAIN LEVEL CA
Page 67 and 68:
CONSTANT RESISTANCE (CR) HIGH RANGE
Page 69 and 70:
CR LOW RANGE TRANSIENT LEVEL CALIBR
Page 71 and 72:
CV READBACK LEVEL CALIBRATION CV re
show all

PEL-60-60-10 - Physical Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?