BARCO PROJECTION SYSTEMS - Log in - Barco

More documents

Recommendations

Info

Packaging and Dimensions Projector Case Dimensions The dimensions are given in mm. 25.4 mm = 1" 46 82.7 211.4 169.5 139.6 14 60 43 124.1 42 124.4 147.8 217.2 148.9 526.8 380.6 368.7 184.4 53.5 371.2 202.4 187.2 53.5 29.6 max 24 min 12 245.1 97.6 120.2 107.5 6 152.6 152.6 2-2 5976309 BARCOGRAPHICS 6400i 04062001
Installation Guidelines 3 INSTALLATION GUIDELINES Safety warning Before installing the projector, read first the safety instructions Installation Guidelines Ambient Temperature Conditions Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to the optimum use of the projection system. Max. ambient temperature : 40 °C or 104 °F Min. ambient temperature : 0 °C or 32 °F The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F). Environment Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust or humidity. Be aware that room heat rises to the ceiling; check that temperature near the installation site is not excessive. Environment condition check Warning: Harmful Environmental Contamination Precaution A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets. For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then measures to relocate the projector to a clean air environment should be considered. Only ever use the manufactures recommended cleaning kit which has been specifically designed for cleaning optical parts, never use industrial strength cleaners on a projectors optics as these will degrade optical coatings and damage sensitive optoelectronic components. Failure to take suitable precautions to protect the projector from the effects of persistant and prolonged air contaminants will culminate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be noneffective and impracticable. Damage of this nature is under no circumstances covered under the manufactures warranty and may deem the warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the environment of the projector. The manufacture reserves the right to refuse repair if a projector has been subject to wantful neglect, abandon or improper use. What about ambient light ? The ambient light level of any room is made up of direct or indirect sunlight and the light fixtures in the room. The amount of ambient light will determine how bright the image will appear. So, avoid direct light on the screen. Windows that face the screen should be covered by opaque drapery while the set is being viewed. It is desirable to install the projection system in a room whose walls and floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level is also important. Too much ambient light will ‘wash out’ of the projected image. This appears as less contrast between the darkest and lightest parts of the image. With bigger screens, the ‘wash out’ becomes more important. As a general rule, darken the room to the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that interference with the screen is minimal. 5976309 BARCOGRAPHICS 6400i 04062001 3-1
Page 1 and 2: BARCO PROJECTION SYSTEMS GRAPHICS 6
Page 3 and 4: Table of Contents 1 TABLE OF CONTEN
Page 5 and 6: Table of Contents AUTO IMAGE ADJUST
Page 7 and 8: Table of Contents Changing the shut
Page 9: Packaging and Dimensions 2 PACKAGIN
Page 13 and 14: Installation Guidelines OFF-Axis in
Page 15 and 16: Installation Guidelines Image 3 Ima
Page 17 and 18: Connections 4 CONNECTIONS Power con
Page 19 and 20: Connections Switching Off To switch
Page 21 and 22: Connections Possible indication : R
Page 23 and 24: Connections Pin configuration mini
Page 25 and 26: Connections RS232 Connection RS232
Page 27 and 28: Connections Audio Connections What
Page 29 and 30: Getting Started 5 GETTING STARTED R
Page 31 and 32: Getting Started Lamp Run Time When
Page 33 and 34: VID E O 3 S-VIDEO SD I R G B H/ C V
Page 35 and 36: Getting Started Controlling the Pro
Page 37 and 38: Start up of the Adjustment Mode 6 S
Page 39 and 40: Auto Image Adjust 7 AUTO IMAGE ADJU
Page 41 and 42: Random Access Adjustment Mode 8 RAN
Page 43 and 44: Random Access Adjustment Mode Load
Page 45 and 46: Random Access Adjustment Mode If th
Page 47 and 48: Random Access Adjustment Mode How t
Page 49 and 50: Random Access Adjustment Mode Pictu
Page 51 and 52: Random Access Adjustment Mode Gamma
Page 53 and 54: Random Access Adjustment Mode Conti
Page 55 and 56: Random Access Adjustment Mode Video
Page 57 and 58: Random Access Adjustment Mode Side
Page 59 and 60: Random Access Adjustment Mode Optio
Page 61 and 62:
Random Access Adjustment Mode How t
Page 63 and 64:
Installation Mode 9 INSTALLATION MO
Page 65 and 66:
Installation Mode Changing the Shut
Page 67 and 68:
Installation Mode Start Up mode Wha
Page 69 and 70:
Installation Mode To define the out
Page 71 and 72:
Installation Mode How to install th
Page 73 and 74:
Service Mode 10 SERVICE MODE Servic
Page 75 and 76:
Service Mode Change Password How to
Page 77 and 78:
Service Mode Entering the new commo
Page 79 and 80:
Service Mode Available settings STA
Page 81 and 82:
Appendix A : Standard Source Set Up
Page 83 and 84:
○ ○ ○ ○ Source Numbers 80 -
Page 85 and 86:
Barco Control Manager C BARCO CONTR
Page 87 and 88:
Barco Control Manager Control Start
Page 89 and 90:
Barco Control Manager Source By cli
Page 91 and 92:
Barco Control Manager Lens adjustme
Page 93 and 94:
Barco Control Manager Audio adjustm
Page 95 and 96:
Barco Control Manager Mail Setup 3
Page 97 and 98:
Barco Control Manager Date & Time T
Page 99 and 100:
Barco Control Manager screen. To en
Page 101 and 102:
Cleaning the Dustfilter D CLEANING
Page 103 and 104:
Index i INDEX A Adjustment Mode Sta
show all

BARCO PROJECTION SYSTEMS - Log in - Barco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?