Manual Verification Tool IMP - Inheco

More documents

Recommendations

Info

6.5.2 Tab „Inclination“ • Select IMP > Real-time view (available only if an IMP Unit is connected). • Select the tab Inclination. The following screen is displayed. On the left side, the force actually acting on the sensors is shown. Is the IMP Unit positioned on its underside (e.g. like image right), so gravity acts on the z sensor with -1.0g. Since no force is acting on x and y sensors in resting position, the chart shows exact vertical, perpendicular position (red dot). Further information ➜ Test Shake Sensors, page 24. INHECO 38
6.6 Time and Date Settings • Select IMP > Time and Date Settings... (available only if an IMP Unit is connected). Following dialogs can be selected by the relevant tab. Check To indicate a potential time difference between IMP Unit and computer. Chose from the possibilities offered to handle the situation. The actual time difference is shown below the radio buttons. If time difference to IMP greater ... minutes To specify a time difference for operating one of the fol - lowing options. auto update IMP time Is this option enabled and the pre-selected time differ - ence has been exceeded, the IMP Server will synchro - nize time automatically to the PC time setting when it is connected. Time data belonging to measurements stored in the IMP is not affected. ask user (show this window) Is this option enabled and the pre-selected time differ - ence has been exceeded, the user will be asked upon connection of the IMP by opening this dialog -for further proceeding and -manual modification of time setting is possible do nothing If the time difference between IMP Unit and computer is insignificant and can be ignored, this is the right option. Time / Date Indicates time / date settings. PC PC time / date. For comparison only (no data input). IMP Sync IMP to PC Done/ Set IMP date / time IMP Unit time / date for manual entry. Synchronizes the IMP Unit on the PC‘s time / date. Time or date settings entered manually can be saved by clicking this button. INHECO 39
Page 1 and 2: INHECO Measurement Plate Part No.:
Page 3 and 4: TABLE OF CONTENTS IMPORTANT NOTES .
Page 5 and 6: 1.2 Warranty Two years from date of
Page 7 and 8: 2.3 Functional Elements Figure 2 in
Page 9 and 10: 2.5 Technical Data IMP Unit Dimensi
Page 11 and 12: 2.8 Status LED Color Type of flashi
Page 13 and 14: 4 SOFTWARE INSTALLATION The followi
Page 15 and 16: After the software and driver insta
Page 17 and 18: INHECO 17
Page 19 and 20: • Click on the button Continue An
Page 21 and 22: 4.5 Uninstall IMP Server Software N
Page 23 and 24: After the selected start delay, the
Page 25 and 26: 5.11 Turn off the IMP Unit • Keep
Page 27 and 28: 6.2 Menu „IMP“ Configure To set
Page 29 and 30: 6.3.2 Section „Start Conditions
Page 31 and 32: 6.3.4 Section „Shaking“ In this
Page 33 and 34: 6.4.1 Tab „Temperature / Humidity
Page 35 and 36: 6.4.2 Tab „Shaking details“ The
Page 37: 6.5 Screen „Real-time View“ Rea
Page 41 and 42: 6.9.1 Tab „Connection“ • Sele
Page 43 and 44: 6.9.3 Tab „Units“ • Select Se
Page 45 and 46: 6.9.5 Tab „Other“ • Select Se
Page 47 and 48: 6.11 Sensor Positions and Shake Dir
Page 49 and 50: 7.7 Disposal The Unit has to be dis

Manual Verification Tool IMP - Inheco

Create successful ePaper yourself

Delete template?

Save as template?