Manual Verification Tool IMP - Inheco

More documents

Recommendations

Info

2.4 Labels The labels on the IMP Unit and the Battery Charger contain important technical indica - tions. The labels must not be removed. If a label has become illegible or falls off, it has to be replaced by a corresponding new label with matching information. New labels can be ordered from INHECO. 14 13 17 15 16 Fig. 3: Labels 13 14 Calibration mark Identification plate 15 16 Identification plate Identification plate 17 Sealing INHECO 8
2.5 Technical Data IMP Unit Dimensions Length 128 mm 5.04 inch Width 86 mm 3.39 inch Height 15 mm 0.59 inch Weight (excluding cables) 100 g 0.273 lbs Input Voltage (USB-Connector) 5 Vdc, ±10% Input Current 0.2 A Fuse internal Interface USB 1.1 or 2.0 Micro-SD-Card 512 MB to 2 GB IrDA Protection Category IP 20 Temperature Sensors 10 digital sensors Shaker Sensor (3 axis) max: ±6g Humidity Sensor 0-100% rel. humidity Battery Charger Input Voltage 100 to 240 V/AC Output Voltage 5 Vdc Input Current 0.4 A Output Current 1.6 A Safety Class 2 Power Frequency 47 to 63 Hz Fuse internal, resettable Environmental Conditions Max. Operation Height 2000 m 6562 ft Tolerable Relative Humidity Operation 100 %, not condensing Battery charging 80 %, not condensing Transportation and storage 80 %, not condensing Temperature Operation +4 to +60°C +41 to +140°F Battery charging 0 to +40°C +32 to +104°F Transportation and storage -10 to +60°C +14 to +140°F Temperature precision 1) Temperature precision ±0.1°C Temperature accuracy ±0.1°C Movement precision 2) Frequence precision ±0.5 Hz Frequence accuracy ±5 % 1) Calibration in water bath. May vary depending on ambient conditions, target temperature and measured device. 2) Measured with the same IMP. INHECO 9
Page 1 and 2: INHECO Measurement Plate Part No.:
Page 3 and 4: TABLE OF CONTENTS IMPORTANT NOTES .
Page 5 and 6: 1.2 Warranty Two years from date of
Page 7: 2.3 Functional Elements Figure 2 in
Page 11 and 12: 2.8 Status LED Color Type of flashi
Page 13 and 14: 4 SOFTWARE INSTALLATION The followi
Page 15 and 16: After the software and driver insta
Page 17 and 18: INHECO 17
Page 19 and 20: • Click on the button Continue An
Page 21 and 22: 4.5 Uninstall IMP Server Software N
Page 23 and 24: After the selected start delay, the
Page 25 and 26: 5.11 Turn off the IMP Unit • Keep
Page 27 and 28: 6.2 Menu „IMP“ Configure To set
Page 29 and 30: 6.3.2 Section „Start Conditions
Page 31 and 32: 6.3.4 Section „Shaking“ In this
Page 33 and 34: 6.4.1 Tab „Temperature / Humidity
Page 35 and 36: 6.4.2 Tab „Shaking details“ The
Page 37 and 38: 6.5 Screen „Real-time View“ Rea
Page 39 and 40: 6.6 Time and Date Settings • Sele
Page 41 and 42: 6.9.1 Tab „Connection“ • Sele
Page 43 and 44: 6.9.3 Tab „Units“ • Select Se
Page 45 and 46: 6.9.5 Tab „Other“ • Select Se
Page 47 and 48: 6.11 Sensor Positions and Shake Dir
Page 49 and 50: 7.7 Disposal The Unit has to be dis

Manual Verification Tool IMP - Inheco

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?