Here - LF-Technik

More documents

Recommendations

Info

12 ______________________________________ Please consider the following menu structure first: Menu Structure GyroBot 900 Wing (and Wing Jet) Software Version V1.11 System Running German / English Calibrate Modell Type Rudder Base Rudder Tuning Elevator Base Elevator Tuning Aileron Base Aileron Tuning Check It Copy Phase Release sticks and press button Standard Rudder Servo centered Rudder Control On/Off Elevator Servos centered Elevator Control On/Off Aileron Servos centered Aileron Control On/Off Inputs from [ ] to [ ] Vibration Filter Rudder Center Rudder P / RC Gain On/Off Elevator Servo 1 Direction Elevator P / RC Gain On/Off Aileron Servo 1 Direction Aileron P / RC Gain On/Off Extension Board Servo Frequency Rudder Minimum Rudder I / RC Gain On/Off Elevator Servo 2 Direction Elevator I / RC Gain On/Off Aileron Servo 2 Direction Aileron I / RC Gain On/Off Gyrosensor Rudder Maximum Rudder Deadband Elevator Servo 1 Center Elevator Deadband Aileron Servo 1 Center Aileron Deadband Accelerometer Rudder Gyro Direction Rudder Airspeed On/Off Elevator Servo 2 Center Elevator Airspeed On/Off Aileron Servo 2 Center Aileron Airspeed On/Off Elevator Minimum Aileron Minimum Elevator Maximum Aileron Maximum Elevator Gyro Direction Aileron Gyro Direction
13 ______________________________________ Declaration of the Flight Phase Switch Gyrobot 900 Wing offers 3 Flight Phases (3 Memories), which can be configured completely free. To switch between these 3 Flight Phases please connect the plug 7 on the GyroBot with a free plug on the Transmitter. Then you need a 3 step switch on the transmitter which switches this channel. You can see the current flight phase in the upper right corner of the GyroBot Display. A switching is only possible in the flying menu “System Running”. You always program the flight phase which you have choosen if you get into the programming menus (pushing the button a little bit longer, starting in „System Running“). Also during programming the current flight phase will be show in the display. You switch completely ALL values (all base and all tuning menus). Later you can copy the values from one to another flight phase in the “Copy Phase” menu. You always copy from the current phase to the phase you choose with the rudder stick. CAUTION: Please be sure that you have programmed (or copied from a programmed one) all flight phases. If you switch into a flight phase which is not programmed your plane will crash immediately. The agility of the separate axes will be adjusted with the servo travel (ATV, Endpoint) of the equal channel on the transmitter. For example if your plane shall fly faster rolls you have to increase the servo travel for the aileron function in the transmitter. Declaration of the Programming You can program the GyroBot 900 Wing either with the Cockpit Programming Box or with the USB Interface Cable and your PC or Laptop. If you use the Cockpit (which is the easiest and most comfortable way), you have to connect the Cockpit with the plug 1 of the GyroBot via the 70 cm Cable. Thereforee please put a 10cm Patchcable (two servo connectors) into plug 1 and then connect this with the 70 cm cable. The other side of the 70 cm cable must be plugged into one of the both connectors of the cockpit, equal which one it is (minus/GND is on the side of the button). The 10 cm Cable can always be left in the model for later programming. If you use a PC or Laptop, please connect the USB Interface Cable to a free USB Slot on the computer and to the 10 cm Cable on slot 1 of the GyroBot. Now you must start and install the file “cockpit.exe” from your GyroBot CD. System Requirements are Windows XP, Windows Vista or Windows 7. Then look for the right COM port in the program and then push the ON/OFF button until the GyroBot Start Menu “System Running” will be shown. Therefore the GyroBot must be connected and under voltage from your receiver battery. If the software does not work please install the following driver. http://www.ftdichip.com/Drivers/CDM/CDM20802_Setup.exe The driver is needed for using the USB Interface Cable, in newer Windows Versions it should not be necessary.
Page 1 and 2: 1 _________________________________
Page 3 and 4: 3 _________________________________
Page 5 and 6: 5 _________________________________
Page 7 and 8: 7 _________________________________
Page 9 and 10: 9 _________________________________
Page 11: 11 ________________________________
Page 15 and 16: 15 ________________________________
Page 17 and 18: 17 ________________________________
Page 19 and 20: 19 ________________________________
Page 21 and 22: 21 ________________________________
Page 23 and 24: 23 ________________________________
Page 25 and 26: 25 ________________________________
Page 27: 27 ________________________________

Here - LF-Technik

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?