Here - LF-Technik

More documents

Recommendations

Info

2 ______________________________________ Index of contents Page Chapter 1 Introduction,Index of Contents 2 Scope of Delivery, What is GyroBot 900 Wing? 4 Which Models are suited? 6 Fixture in the Model 11 Plug Connection on GyroBot and Extensionboard 12 Menu Struktur 13 Declaration of the Flight Phase Switch and of the Programming 14 Programming of the GyroBot 900 Wing and Jet 21 Declaration of P- and I Part 22 Declaration of "RC-Gain" 23 Declaration of "Airspeed" 24 Declaration of Trimming with the GyroBot 900 Wing and Jet 26 The first Flight 28 Installation of Software-Updates 29 Technical Data Scope of Delivery Depending on which components you ordered, the following parts are included in the box: Ord.No. 5002: 1. GyroBot 900 Wing with Extension Board and Pitot Tube 2. 7 three pole cables (double sides servo connector male) with a length of 10cm (optional other lenghtes are available) 3. 4m of Festo 3mm Tube 4. 2 Festo Connectors 3mm 5. 3 Self-Adhesive Pads 6. CD with Software und Manual 7. Decals Ord.No. 5000/1: 1. USB Interface Cable (to program via PC or Laptop and for updating) Ord.No. 5000/2: 1. „Cockpit“ Programming Box (to program without your PC) 2. 1 three pole cable (servo connector male-servo connector female)
3 ______________________________________ Ord. No. 5002 Ord. No. 5000/1 Ord. No. 5000/2 What is GyroBot 900 Wing? It is a world novelty. The GyroBot 900 Wing is a high-quality and precise flight control system with stabilisation of the aileron, elevator and rudder axis of a model airplane. Aileron, elevator and rudder ar controlled by the GyroBot. Thereby the flight characteristics of each plane will be improved of that effect that the model flies „like on rails“. A fully adjusted GyroBot 900 Wing will always keep the model in the position you brought it to with the control sticks. But it never works against your inputs from the transmitter. The throttle function is not considered. This means for you: The model flies much better and more precise as without GyroBot, flying will be much easier. For example flying aerobatics is much easier because the GyroBot controls all „static“ figures itself after you brought the model into the right position. You must not switch on and off the GyroBot for doing aerobatic figures. You can fly the whole flight (except of the start and landing) with active GyroBot on all 3 axes (if you use an aerobatic machine). Figures like inverted, knife edge, hovering and torqueroll are completely controlled by the GyroBot. You only have to bring the model into the right position and then loose the stick (except of the throttle). During normal flight you only have to move the sticks if you want to change the direction or position of the plane, but you don´t have to do anything against restlessness of the plane or against wind impacts. GyroBot always keeps the model in the relative position, it does not orient itself on the horizon or on the cardinal points. GyroBot 900 Wing is not authorized for turbine powered Jetmodels!!! What is GyroBot 900 Wing Jet? GyroBot 900 Wing Jet is a version of GyroBot 900 Wing which is authorized for operating in Gas Turbine Jets. It is also authorized for all other kinds of model airplanes and it can be handled and programmed similar to the GyroBot 900 Wing. The only „disadvantage“ ist the higher weight and the bigger case. For flying Gas Turbine Jets you MUST use GyroBot 900 Wing Jet!!! Can I switch on and off the GyroBot during flight? Yes, via the flight phases. GyroBot 900 Wing has 3 flight phases which can be configured completely free. The control of each axis can be switched on or off during flight via switching between the different flight phases. For example if the control is off for all 3 axes in flight phase 1 and the control is on for all 3 axes in flight phase 2 you can switch between control off and on via switching between flight phase 1 and 2 during flight. For example you only can put on the control for the rudder (or elevator, or ailerons) in one flight phase.
Page 1: 1 _________________________________
Page 5 and 6: 5 _________________________________
Page 7 and 8: 7 _________________________________
Page 9 and 10: 9 _________________________________
Page 11 and 12: 11 ________________________________
Page 13 and 14: 13 ________________________________
Page 15 and 16: 15 ________________________________
Page 17 and 18: 17 ________________________________
Page 19 and 20: 19 ________________________________
Page 21 and 22: 21 ________________________________
Page 23 and 24: 23 ________________________________
Page 25 and 26: 25 ________________________________
Page 27: 27 ________________________________

Here - LF-Technik

Create successful ePaper yourself

Delete template?

Save as template?