SterilGARD III Advance SG403 / SG603 - Baker Company

More documents

Recommendations

Info

Positive and Negative Pressure Areas All positive pressure plenums in the cabinet, the work area and the unipressure flow system, are surrounded by negative pressure. If a leak should occur in the positive pressure plenum, the suction from the blower will capture the air from the leak and recirculate it. Also, if a leak should occur in a contaminated negative pressure plenum, such as the sidewall or rear wall, the suction will pull air in through the leak. Thus contaminated air in a negative pressure plenum will not leak out into the room. 8
Chapter II INSTALLING THE CABINET Checking the Cabinet Upon Arrival Upon receipt of your new SterilGARD®III Advanceº cabinet, inspect the outside of the crate and skid for broken glass, holes in the cardboard box, or any other damage. Record any visible damage on the receiving slip and report it to the delivering carrier immediately. Open the box and inspect the cabinet. Remove the cabinet from the skid with a forklift. Parts of the cabinet are packaged separately. Check the packing slip carefully to be sure that all items have been located. If any damage or loss is found it should be reported to the delivering carrier. A claim for restitution should be filed within 15 days. Cabinet Location Proper placement within the laboratory is essential! The ideal location for any BSC is in a dead-end corner of the laboratory. A dead end corner is an inside corner of the room not next to a window or door. The cabinet must be located away from personnel traffic, HVAC vents, doors, windows and anything else that will cause disruptive air currents. It is important that there be free space of 2" between the top of the cabinet and the ceiling. If the ceiling is too low it will restrict the air exiting the cabinet. This affects the amount of air entering the cabinet. If your ceiling is less than 2” above the top of the cabinet, call Customer Service. Installation Installation of this cabinet should be carried out in accordance with appropriate regulations. 1 Remove the protective container from around the cabinet. 2 Remove the strapping that holds the cabinet to the pallet. 3 Referring to drawing # 333464 attached to the viewscreen remove the packing material that secures the view screen and install thumb screw hardware where noted to fusillade servicing and cleaning. 4 Remove the small cardboard box taped to the work surface and take out the drain valve, piping adapter, and exhaust filter protector. 5 Install the exhaust filter protective screen on top of the exhaust damper using the two cap nuts installed on the damper. 6 Refer to chapter VI for tubular base stand set up and adjustment. 9
Page 1 and 2: OPERATOR’S MANUAL Baker SterilGAR
Page 3 and 4: WARRANTY The Baker Company, Inc. ex
Page 5 and 6: Chapter I THE SterilGARD®III Advan
Page 7 and 8: Controls Controls and alarms are lo
Page 9: AIRFLOW DIAGRAM The flow of air ins
Page 13 and 14: Chapter III TESTING THE CABINET PRI
Page 15 and 16: 4 Seal off the exhaust opening by t
Page 17 and 18: 22. Decrease the motor / blower vol
Page 19 and 20: 20409. and NSF Standard 49 1992 Cla
Page 21 and 22: HEPA Filters HEPA Filter Cautions 1
Page 23 and 24: 14 Alternately loosen the ½ -13 pl
Page 25 and 26: When there is low airflow within th
Page 27 and 28: Chapter VI Stand Assembly/Leg Exten
Page 29 and 30: 7. Unscrew the bolts (one per leg)
Page 31 and 32: Chapter VII Specifications Weight S
Page 35 and 36: Replacement Parts MODEL SG403EN SG6
Page 37: 9 Decontaminate all equipment, whic

SterilGARD III Advance SG403 / SG603 - Baker Company

Create successful ePaper yourself

Delete template?

Save as template?