15" PLANER INSTRUCTION MANUAL - Grizzly Industrial Inc.

More documents

Recommendations

Info

Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE ASSEMBLY PROCESS! MEASURE BOLT DIAMETER BY PLACING INSIDE CIRCLE 4mm 6mm 8mm 10mm 12mm 16mm # 10 1 ⁄4'' 5 ⁄16'' 3 ⁄8'' 7 ⁄16'' 1 ⁄2'' 5 ⁄8'' LINES ARE 1MM APART Thumb Screw Cap Screw Setscrew Washer 5mm 10mm 15mm 20mm 25mm 30mm 35mm 40mm 45mm 50mm 55mm 60mm 65mm 70mm 75mm 1 ⁄4'' 3 ⁄8'' 1 ⁄2'' 5 ⁄8'' Phillips Head Screw Carriage Bolt Hex Head Bolt Lock Washer LINES ARE 1 ⁄16'' INCH APART Countersunk Phillips Head Screw -12- G0550/G0551 15" Planer Lock Nut Hex Nut 5 ⁄16'' 7 ⁄16'' 9 ⁄16'' 3 ⁄4'' 7 ⁄8'' 1'' 1 1 ⁄4'' 1 1 ⁄2'' 1 3 ⁄4'' 2 2 1 ⁄4'' 2 1 ⁄2'' 2 3 ⁄4'' 3 Flange Bolt Phillips Head Hex Bolt WASHERS ARE MEASURED BY THE INSIDE DIAMETER Wing Nut 12mm WASHER DIAMETER 10mm WASHER DIAMETER 8mm WASHER DIAMETER Slotted Screw Button Head Screw Phillips Head Sheet Metal Screw WASHER DIAMETER 4mm WASHER DIAMETER 6mm ASHER DIAMETER W5⁄8'' 9 ⁄16'' WASHER DIAMETER 1 ⁄2'' WASHER DIAMETER 7 ⁄16'' WASHER DIAMETER 3 ⁄8'' WASHER DIAMETER 5 ⁄16'' WASHER DIAMETER 1 ⁄4'' WASHER DIAMETER WASHER DIAMETER # 10
Site Considerations Clean Up Floor Load The Model G0550 weighs 410 lbs and has a 25" x 25" footprint. The Model G0551 weighs 450 lbs and has a 21" x 21" footprint. Most commercial floors are suitable for the machine. Some residential floors may require additional reinforcement to support both the machine and operator. Working Clearances Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for the machine. See Figure 6 for the overall dimensions of the Model G0550/G0551. 28" 48" The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as <strong>Grizzly</strong>’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For optimum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Gasoline and petroleum products have low flash points and could explode if used to clean machinery. DO NOT use gasoline or petroleum products to clean the machinery. Figure 6. Overall machine dimensions. Smoking near solvents could ignite an explosion or fire and cause serious injury. DO NOT smoke while using solvents. Unsupervised children and visitors inside your shop could receive serious personal injury. Ensure child and visitor safety by keeping all entrances to the shop locked at all times. DO NOT allow unsupervised children or visitors in the shop at any time. Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingested. Lack of ventilation while using these solvents could cause serious personal health risks or fire. Take precautions from this hazard by only using cleaning solvents in a well ventilated area. G0550/G0551 15" Planer -13-
Page 1 and 2: 15" PLANER MODEL G0550/G0551 INSTRU
Page 3 and 4: Table Of Contents SECTION 1: SAFETY
Page 5 and 6: Safety Instructions For Power Tools
Page 7 and 8: SECTION 2: INTRODUCTION Commentary
Page 9 and 10: Circuit Capacity Extension Cords Al
Page 11 and 12: Common Terms & Definitions Work Tab
Page 13: H F G A E A B C E D B Figure 4. G05
Page 17 and 18: 2. Connect the remaining legs and b
Page 19 and 20: Extension Rollers 5. Loosen the bed
Page 21 and 22: Start Up Recommended Adjustments St
Page 23 and 24: Power Feed Handwheel The power feed
Page 25 and 26: SECTION 7: MAINTENANCE Maintenance
Page 27 and 28: Gearbox Lubrication The gearbox is
Page 29 and 30: Planing Difficulties The species of
Page 31 and 32: Table Adjustment It is important th
Page 33 and 34: Knife Inspection The Model G0550/G0
Page 35 and 36: 4. Place the knife setting jig over
Page 37 and 38: 6. Repeat steps 1-5 for the opposit
Page 39 and 40: 4. Remove the springs that are in t
Page 41 and 42: Aftermarket Accessories To order an
Page 43 and 44: MACHINE DATA SHEET Customer Service
Page 45 and 46: 55 116 111 113 114 112 3 22 115 117
Page 47 and 48: REF PART # DESCRIPTION 1 P0550001 P
Page 49 and 50: Troubleshooting Guide SYMPTOM Motor
Page 51 and 52: Gauge Block Measurements G0550/G055
Page 53 and 54: WARRANTY CARD Name ________________
Page 56: Buy Direct and Save with Grizzly ®

15" PLANER INSTRUCTION MANUAL - Grizzly Industrial Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?