15" PLANER INSTRUCTION MANUAL - Grizzly Industrial Inc.

More documents

Recommendations

Info

SECTION 3: CIRCUIT REQUIREMENTS Amperage Draw Plug-Type The Model G0550/G0551 motor is wired to operate at 220V only. The planer motors draw the following amperage: Amperage Draw G0550 2 HP..........................................12 Amps G0551 3 HP..........................................18 Amps We recommend using a NEMA-style 6-15 plug and outlet with the G0550 as shown in Figure 1a and an L6-20 plug and outlet for the G0551 as shown in Figure 1b. You may also “hard-wire” the planer directly to your panel, provided you place a disconnect near the machine. Check the electrical codes in your area for specifics on wiring requirements. Circuit Breaker Use the following guidelines when choosing a circuit breaker (circuit breakers rated any higher are not adequate to protect the circuit): Circuit Breaker G0550 ........................................15 Amp, 2 Pole G0551 ........................................20 Amp, 2 Pole Figure 1a. NEMA 6-15 plug and receptacle. Figure 1b. NEMA L6-20 plug and receptacle. -6- G0550/G0551 15" Planer
Circuit Capacity Extension Cords Always check to see if the wires in your circuit are capable of handling the amperage draw from your machine, as well as any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electrician. If the circuit breaker trips or the fuse blows regularly, your machine may be operating on a circuit that is close to its amperage draw capacity. However, if an unusual amperage draw does not exist and a power failure still occurs, contact a qualified electrician. Grounding 220V Operation We do not recommend the use of extension cords on 220V equipment. Instead, arrange the placement of your equipment and the installed wiring to eliminate the need for extension cords. If you find it absolutely necessary to use an extension cord at 220V with your <strong>Grizzly</strong> Planer: • Make sure the cord is rated for Standard Service (grade S) or better. • The extension cord must also contain a ground wire and plug prong. • Use at least a 16 gauge cord if the cord is 50 feet long or less. • Use at least a 14 gauge cord if the cord is between 51-100 feet. Electrocution or a fire can result if the machine is not grounded correctly. Make sure all electrical circuits are grounded. DO NOT use the machine if it is not grounded. In the event of an electrical short, grounding reduces the risk of electric shock by providing a path of least resistance to disperse electric current. This tool is equipped with a power cord that has an equipment-grounding prong. The outlet must be properly installed and grounded in accordance with all local codes and ordinances. G0550/G0551 15" Planer -7-
Page 1 and 2: 15" PLANER MODEL G0550/G0551 INSTRU
Page 3 and 4: Table Of Contents SECTION 1: SAFETY
Page 5 and 6: Safety Instructions For Power Tools
Page 7: SECTION 2: INTRODUCTION Commentary
Page 11 and 12: Common Terms & Definitions Work Tab
Page 13 and 14: H F G A E A B C E D B Figure 4. G05
Page 15 and 16: Site Considerations Clean Up Floor
Page 17 and 18: 2. Connect the remaining legs and b
Page 19 and 20: Extension Rollers 5. Loosen the bed
Page 21 and 22: Start Up Recommended Adjustments St
Page 23 and 24: Power Feed Handwheel The power feed
Page 25 and 26: SECTION 7: MAINTENANCE Maintenance
Page 27 and 28: Gearbox Lubrication The gearbox is
Page 29 and 30: Planing Difficulties The species of
Page 31 and 32: Table Adjustment It is important th
Page 33 and 34: Knife Inspection The Model G0550/G0
Page 35 and 36: 4. Place the knife setting jig over
Page 37 and 38: 6. Repeat steps 1-5 for the opposit
Page 39 and 40: 4. Remove the springs that are in t
Page 41 and 42: Aftermarket Accessories To order an
Page 43 and 44: MACHINE DATA SHEET Customer Service
Page 45 and 46: 55 116 111 113 114 112 3 22 115 117
Page 47 and 48: REF PART # DESCRIPTION 1 P0550001 P
Page 49 and 50: Troubleshooting Guide SYMPTOM Motor
Page 51 and 52: Gauge Block Measurements G0550/G055
Page 53 and 54: WARRANTY CARD Name ________________
Page 56: Buy Direct and Save with Grizzly ®

15" PLANER INSTRUCTION MANUAL - Grizzly Industrial Inc.

Create successful ePaper yourself

Delete template?

Save as template?