flasher stm8.pdf - SEGGER Microcontroller

More documents

Recommendations

Info

12 CHAPTER 1 Introduction 1.3 Flasher STM8 features • USB 2.0 interface • Full duplex 100Mbit ethernet interface • Any STM8 core supported • No power supply required, powered through USB • Target voltage can be measured • Fully plug and play compatible • Standard 4-pin SWIM connector • USB, ethernet, RS232 and 4-pin ribbon cable included • TCP/IP server included in Flasher STM8, which allows using Flasher via TCP/IP networks • Flash programming software available • Integrated optical isolation between host and target system • Target power supply via pin 1 of the 4-pin interface (up to 300mA to target with overload protection) Flasher STM8 (UM05006) © 2011 SEGGER Microcontroller GmbH & Co. KG
1.4 Supported CPU cores Flasher STM8 has been designed and tested with the following cores, but should work with any STM8 core. If you experience problems with a particular core, do not hesitate to contact Segger. • STM8A • STM8L • STM8S Flasher STM8 (UM05006) © 2011 SEGGER Microcontroller GmbH & Co. KG 13
Page 1 and 2: Flasher STM8 User guide of the stan
Page 3 and 4: Revisions This manual describes the
Page 5 and 6: About this document This document d
Page 7 and 8: 7 Table of Contents 1 Introduction
Page 9 and 10: Chapter 1 Introduction This chapter
Page 11: 1.2 Specifications 1.2.1 Specificat
Page 15 and 16: Chapter 2 Setup This chapter descri
Page 17 and 18: 2. Accept the default installation
Page 19 and 20: 2.2 Setting up the USB interface Af
Page 21 and 22: 2.3 Uninstalling the J-Link USB dri
Page 23 and 24: 2.4.1.2 Connecting via Ethernet onl
Page 25 and 26: 2.4.2.2 Configuring Flasher via web
Page 27 and 28: Chapter 3 Flasher STM8 related soft
Page 29 and 30: 3.2 Flasher STM8 software and docum
Page 31 and 32: 3.3 Using the JLinkSTM8.dll 3.3.1 W
Page 33 and 34: Chapter 4 Working with Flasher STM8
Page 35 and 36: 4.1.1.2 Setting up Flasher STM8 for
Page 37 and 38: After the download, you should see
Page 39 and 40: 4.2 Multiple File Support It is als
Page 41 and 42: 2. Use "File->Save programmer confi
Page 43 and 44: 9. Download the files from your tem
Page 45 and 46: 4.3.2 Configuring multiple Flasher
Page 47 and 48: Chapter 5 Remote control This chapt
Page 49 and 50: 5.2 Handshake control Flasher STM8
Page 51 and 52: #AUTO NOINFO This command may be us
Page 53 and 54: #FDELETE flasher.dat #ACK #OK Note:
Page 55 and 56: Message Description #STATUS:ERASING
Page 57 and 58: Chapter 6 Hardware This chapter giv
Page 59 and 60: 6.2 4-pin Connector Flasher STM8 ha
Page 61 and 62: 6.4 Target board design for SWIM We
Page 63 and 64:
Chapter 7 Background information Th
Page 65 and 66:
Chapter 8 Support and FAQs This cha
Page 67 and 68:
8.2 Frequently Asked Questions Maxi
Page 69 and 70:
Chapter 9 Glossary This chapter des
Page 71 and 72:
Chapter 10 Literature and reference
Page 73 and 74:
B Big-endian ......................
show all

flasher stm8.pdf - SEGGER Microcontroller

Create successful ePaper yourself

Delete template?

Save as template?