flasher stm8.pdf - SEGGER Microcontroller

More documents

Recommendations

Info

40 CHAPTER 4 Working with Flasher STM8 4.2.1 Setting up configurations and switching configurations The following steps describe the way to setup and use multiple configurations and how they can be exchanged using the STM8 Commander. Setup and exchanging configurations can be done via RS232 the same way except that the way of file access is slightly different using the ASCII command interface as described in ASCII command interface on page 50. 1. Setup your first configuration you wish to use with the Flasher using Flasher STM8 Software. Flasher STM8 (UM05006) © 2011 SEGGER Microcontroller GmbH & Co. KG
2. Use "File->Save programmer configuration file..." and save as "Flasher1.cfg" to a temporary directory. 3. Use "File->Save programmer data file..." and save as "Flasher1.dat" to a temporary directory. Flasher STM8 (UM05006) © 2011 SEGGER Microcontroller GmbH & Co. KG 41
Page 1 and 2: Flasher STM8 User guide of the stan
Page 3 and 4: Revisions This manual describes the
Page 5 and 6: About this document This document d
Page 7 and 8: 7 Table of Contents 1 Introduction
Page 9 and 10: Chapter 1 Introduction This chapter
Page 11 and 12: 1.2 Specifications 1.2.1 Specificat
Page 13 and 14: 1.4 Supported CPU cores Flasher STM
Page 15 and 16: Chapter 2 Setup This chapter descri
Page 17 and 18: 2. Accept the default installation
Page 19 and 20: 2.2 Setting up the USB interface Af
Page 21 and 22: 2.3 Uninstalling the J-Link USB dri
Page 23 and 24: 2.4.1.2 Connecting via Ethernet onl
Page 25 and 26: 2.4.2.2 Configuring Flasher via web
Page 27 and 28: Chapter 3 Flasher STM8 related soft
Page 29 and 30: 3.2 Flasher STM8 software and docum
Page 31 and 32: 3.3 Using the JLinkSTM8.dll 3.3.1 W
Page 33 and 34: Chapter 4 Working with Flasher STM8
Page 35 and 36: 4.1.1.2 Setting up Flasher STM8 for
Page 37 and 38: After the download, you should see
Page 39: 4.2 Multiple File Support It is als
Page 43 and 44: 9. Download the files from your tem
Page 45 and 46: 4.3.2 Configuring multiple Flasher
Page 47 and 48: Chapter 5 Remote control This chapt
Page 49 and 50: 5.2 Handshake control Flasher STM8
Page 51 and 52: #AUTO NOINFO This command may be us
Page 53 and 54: #FDELETE flasher.dat #ACK #OK Note:
Page 55 and 56: Message Description #STATUS:ERASING
Page 57 and 58: Chapter 6 Hardware This chapter giv
Page 59 and 60: 6.2 4-pin Connector Flasher STM8 ha
Page 61 and 62: 6.4 Target board design for SWIM We
Page 63 and 64: Chapter 7 Background information Th
Page 65 and 66: Chapter 8 Support and FAQs This cha
Page 67 and 68: 8.2 Frequently Asked Questions Maxi
Page 69 and 70: Chapter 9 Glossary This chapter des
Page 71 and 72: Chapter 10 Literature and reference
Page 73 and 74: B Big-endian ......................

flasher stm8.pdf - SEGGER Microcontroller

Create successful ePaper yourself

Delete template?

Save as template?