10 in. TABLE SAW - Sears

More documents

Recommendations

Info

TOINS'i'ALLBLADEGUARDASSEMBLY See Figure 23. Proper installationof the blade guardassemblymeans that the saw blade and rivingknifeare in alignment. ALWAYSalign the rivingknife to the saw b/ade priorto turning on the table saw. • Lower the blade and removethe throat plate. • Make sure the bevellooldng leveris securelypushedto the (eft. Raise the saw blade to its full heightby turning the height/bevel adjustinghandwheelclockwise. • Loosen the two hex nutsenoughto slide the riving knife down between the shims. Do not remove the he]
CAUSES OF KICKBACK Kickback can occur when the blade stallsor binds, kicking the workpieca back toward youwith greatforce and speed. If your handsare near the saw blade, they may be jerked loosefromthe workpieceand may contactthe blade. Kickback can cause seriousinjury.Use precautions to avoidthe risks. Kickback can be caused by any action that pinchesthe blade in the wood such as: • Making a cut with incorrect blade depth • Sawlng into knots or nailsin the workpiece • Twistingthe wood while makinga out • Failingto supportwork • Forcinga cut • Cutting warped orwet lumber • Us{ngthe wrong blade for the type of cut • Not following oorrect operatingprocedures • Misusingthe saw • Failingto use the an_-kick.baokpawls • Cutting with a dull, gummed-up, or h'npmperiy set b_ad_ AVOIDING KICKBACK • Always use the correct blade depth setting.The top of the blade teeth shouldclearthe workpieceby 1/8 in. to 114in. • Inspect the work for knotsor nailsbefore beginninga cut KnocY,out any loose knotsw_tha hamme_'.Never saw into a loose knot orna|(. • Always use the rip fence when rip cuttingand the miter gauge when crosscutting.This helps preventtwisting the wood inthe cut. • Always use cLsan,sharp, and properly-setblades, Never make outs with dullblades. • TOavoid pinchingthe blade, supportthe work properly before beginninga cut, • When making a cut. usesteady,even pressure. Never force outs. • Do not cut wet orwarped lumber. • Always herdyour workplece fLrmtywith both hands or with push sticks.Keep your body in a balanoed position to be ready to resist kickbackshould it occur. Never stand direc_y in line withthe blade. • Use the righttype of blade for the cut being made. 23 CUTTING AIDS See Figure 24. Pushsticksare devicesused for safelypushinga workpLscethroughthe blade.They can be made _'orn scrapwood invarioussizes and shapesto be usedin a specific project.The stick must be narrowerthan the workpieoe,with s g0° notchin one end and shapingfor a gripon the other end. A push block has a handle fastened by recessed screws from the underside. Use it on non-throughcuts. CAUTION: Be surethe screws in a push blockare recessedto avoid damagingthe saw orworkpiece. PUStlSTICKS Rg. 24
Page 1 and 2: Operator's Manual 10 in. TABLE SAW
Page 3 and 4: _k WARNING." Reed and understand al
Page 5 and 6: • NEVER perform any operation =fr
Page 7 and 8: The following signetwords and meani
Page 9 and 10: Anti-Kickback Pawla (radial arm and
Page 11 and 12: KNOW YOUR TABLE SAW See Figure 2. B
Page 13 and 14: BLADES Formaximum performance,it is
Page 15 and 16: Thefolidwing items are includedwith
Page 17 and 18: TOSECURE/LEVELTHESAW See F-igum9. W
Page 19 and 20: TOUNLOCK/MOVETHERAILS See Figure 15
Page 21: I!_STIIIG CI_II, N[P MITERFENCE KNO
Page 25 and 26: FEATHERBOARD A fsatherboard is a de
Page 27 and 28: • Remove framinQ, square and slid
Page 29 and 30: • Tightenhex nut securely. • Ad
Page 31 and 32: MAKINGCUTS Thebladeprovidedwiththe
Page 33 and 34: VIEWEDFROMTHEFRONT,BELOWTHETABLESAW
Page 35 and 36: MAKING A LARGE PANEL CUT See Figure
Page 37 and 38: ACCESSORY TABLE USAGE Th|s accessor
Page 39 and 40: TOINSTALLROUTER See Ftgure55. • U
Page 41 and 42: TOCHECK,REPLACE,ORADJUSTTHERIVING K
Page 43 and 44: TOCHECKTHEALIGNMENTOFTHERIPFENCE TO
Page 45 and 46: A Am, WARNING: When servicing,use o
Page 47 and 48: I PROBLEM CAUSE SOLUTION ! Wood edg
Page 49 and 50: CRAFTSMAN 10 in. TABLE SAW - MODEL
Page 51 and 52: k , 2o CRAFTSMAN 10 in. TABLE SAW-
Page 53 and 54: tl CRAFTSMAN t0 in. TABLE SAW - MOD

10 in. TABLE SAW - Sears

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?