Single Pillow Block - Heavy Series - Houston Bearing and Supply

PAGE 15
Four Bolt Flange - Heavy Series
Replaces Fafnir RCJO and INA RCJO
The Ketchie-Houston heavy series four bolt
flange unit is similar in design to the standard
series. They are for applications where
minimum amount of machining is to be done
and are supplied completely assembled, being
mounted in place by means of bolts through
the flange.
KETCHIE-HOUSTON, INC.
These units are equipped with a heavy series
wide inner ring bearing with integral seals and
eccentric locking collar.
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR’S PART NUMBER
Ketchie Replaces Shaft A B C D E F G H J K Bolt Bearing Approx.
Houston Diam. Size Number Unit
Fafnir INA (4 req’d) Wt.
in. in. in. in in. in. in. in. in. in. in. in. lbs
mm mm mm mm mm mm mm mm mm mm mm
KH-2100-12A RCJO RCJO 1 3 /16 4 3 /4 3 5 /8 9
/16 1 1 /2 2 3 /32 9
/16
19
/32 1 31 /32 3 13 /16 1 15 /16
120.6 92.08 14.3 38.1 53.2 14.3 15.1 50.0 96.8 49.2
1
/2 GHWE103CCS 4.25
KH-2101-10A 1 1 /4 5 1 /8 4 5
/8 1 19 /32 2 5 /32 9
/16 9
/16 2 1 /32 4 1 /8 2 3 /16 1
/2 GHWE104CCS
KH-2101-12A RCJO RCJO 1 3 /8 130.2 101.6 15.9 40.5 54.8 14.3 14.3 51.6 104.8 58.7 GHWE106CCS 5.75
KH-2101-13A 1 7 /16 GHWE107CCS
KH-2101-10A RCJO RCJO 1 1 /2 5 3 /8 4 1 /8 5
/8 1 3 /4 2 3 /8 5
/8 5
/8 2 1 /4 4 1 /2 2 1 /2 9 /16 GHWE108CCS 7.00
136.5 104.78 15.9 44.4 60.3 15.9 15.9 57.2 114.3 63.5
KH-2103-10A 1 5 /8 5 5 /8 4 3 /8 11 /16 1 27 /32 2 7 /16 5
/8
19
/32 2 5 /16 4 7 /8 2 3 /4 9 /16 GHWE110CCS
KH-2103-11A RCJO RCJO 1 11 /16 142.9 111.12 17.5 46.8 61.9 15.9 15.1 58.7 123.8 69.8 GHWE111CCS 8.00
KH-2303-12A 1 3 /4 GHWE112CCS
KH-2104-12A RCJO RCJO 1 15 /16 6 1 /2 5 1 /8 11 /16 2 3 /32 2 3 /4 11 /16
21
/32 2 5 /8 5 9 /16 3 5
/8 GHWE115CCS 11.75
165.1 130.18 17.5 53.2 69.8 17.5 16.7 66.7 141.3 76.2
KH-2105-10A RCJO RCJO 2 7 5 5 /8 11 /16 2 5 /16 3 11 /16 11 /16 2 7 /8 6 1 /16 3 1 /4 5
/8 GHWE200CCS 14.25
KH-2105-13A 2 3 /16 177.8 142.88 17.5 58.7 76.2 17.5 17.5 73.0 154.0 82.6 GHWE203CCS
KH-2106-13A RCJO RCJO 2 7 /16 7 1 /2 5 7 /8 3
/4 2 9 /16 3 5 /16 13 /16 3
/4 3 1 /8 6 5 /16 3 1 /2
190.5 149.22 19.0 65.1 84.1 20.6 19.0 79.4 160.3 88.9
3
/4 GHWE207CCS 16.50
KH-2107-10A RCJO RCJO 2 11 /16 8 7 /8 7 7
/8 2 27 /32 3 11 /16 15 /16
27
/32 3 1 /2 7 5 /16 4 7
/8 GHWE211CCS 21.25
225.4 177.8 22.2 72..2 93.7 23.8 21.4 88.9 185.7 101.6
KH-2108-10A RCJO RCJO 2 15 /16 9 1 /8 7 1 /4 7
/8 3 1 /16 4 1 /8 15 /16 1 1 /16 3 15 /16 7 13 /16 4 7 /16
231.8 184.15 22.2 77.8 104.8 23.8 27.0 100.0 198.4 112.7
7
/8 GHWE215CCS 31.25
KH-2109-10A RCJO RCJO 3 7 /16 11 8 1 /2 1 1 /8 3 5 /16 4 3 /4 1 1 /16 1 7 /16 4 9 /16 9 5 13 /64 1 GHWE307CCS 47.50
279.4 215.9 28.6 84.1 120.6 27.0 36.5 115.9 228.6 132.2
KH-2110-10A RCJO RCJO 3 15 /16 12 1 /2 9 1 /2 1 1 /4 3 13 /16 5 1 /4 1 3 /16 1 7 /16 5 1 /16 10 1 /2 5 47 /64 1 1 /8 GHWE315CCS 67.75
317.5 241.3 31.8 96.8 133.4 30.2 36.5 128.6 266.7 145.7
Recommended shaft tolerances: 1 3 /16 ” - 1 15 /16", nominal to – .0005", – .013 mm; 2” - 3 15 /16", nominal to – .0010", – .025 mm