Single Pillow Block - Heavy Series - Houston Bearing and Supply

KETCHIE-HOUSTON, INC. PAGE 72
Lineshaft Boxes - Standard Series
Replaces Fafnir F Type
The Ketchie-Houston standard series
lineshaft box or hanger box unit. They are
made for replacing plain or roller bearing
boxes. Installed as a single unit, they require
no internal adjustments.
These units are equipped with two standard
series inner ring bearings with one seal arrangement
and eccentric locking collar on
each insert.
TO ORDER, SPECIFY KETCHIE-HOUSTON OR COMPETITOR’S PART NUMBER
Ketchie Replaces Shaft A B C D Bearing Number Approx.
Houston Fafnir Diam. (2 Required) Unit
Wt.
in. in. in. in in lbs.
KH-3150-0A F
13
/16 SWE013CC 3.75
KH-3150-1A F 7
/8 2 1 /16 2 1 /16 4 15 /16 2 9 /16 SWE014CC 3.75
KH-3150-2A F
15
/16 SWE015CC 3.50
KH-3150-3A F 1 SWE100CC 3.50
KH-3151-0A F 1 1 /16 SWE101CC 5.00
KH-3151-1A F 1 1 /8 2 5 /16 2 5 /16 5 5 /8 2 31 /32 SWE102CC 5.00
KH-3151-2A F 1 3 /16 SWE103CC 4.75
KH-3152-0A F 1 1 /4 SWE104CC 7.75
KH-3152-1A F 1 5 /16 2 9 /16 3 1 /16 6 3 /8 3 5 /8 SWE105CC 7.50
KH-3152-2A F 1 3 /8 SWE106CC 7.25
KH-3152-3A F 1 7 /16 SWE107CC 7.25
KH-3153-0A F 1 1 /2 3 1 /16 3 3 /16 6 3 /4 3 7 /8 SWE108CC 8.75
KH-3153-1A F 1 9 /16 SWE109CC 8.50
KH-3154-0A F 1 5 /8 SWE110CC 10.25
KH-3154-1A F 1 11 /16 3 1 /16 3 3 /16 6 3 /4 4 SWE111CC 10.25
KH-3154-2A F 1 3 /4 SWE112CC 9.75
KH-3155-0A F 1 13 /16 SWE113CC 12.75
KH-3155-1A F 1 7 /8 3 3 /8 3 3 /4 7 3 /8 4 5 /16 SWE114CC 12.50
KH-3155-2A F 1 15 /16 SWE115CC 12.25
KH-3156-0A F 2 SWE200CC 16.25
KH-3156-1A F 2 1 /16 3 5 /8 3 7 /8 8 4 11 /16 SWE201CC 15.50
KH-3156-2A F 2 1 /8 SWE202CC 15.25
KH-3156-3A F 2 3 /16 SWE203CC 15.00
KH-3157-0A F 2 1 /4 SWE204CC 21.25
KH-3157-1A F 2 5 /16 4 1 /8 4 15 /32 8 7 /16 5 1 /4 SWE205CC 21.25
KH-3157-2A F 2 3 /8 SWE206CC 20.50
KH-3157-3A F 2 7 /16 SWE207CC 20.25
KH-3158-0A F 2 1 /2 4 3 /8 4 9 /16 9 1 /8 5 5 /8 SWE208CC 25.25
KH-3159-1A F 2 11 /16 SWE211CC 24.25
KH-3160-2A F 2 15 /16 4 7 /8 5 10 6 1 /2 SWE215CC 32.25
KH-3161-3A F 3 3 /16 5 1 /4 5 1 /4 11 6 9 /16 SWE303CC 45.25
KH-3162-3A F 3 7 /16 5 3 /4 6 1 /2 11 7 /8 7 1 /8 SWE307CC 53.25
KH-3163-3A F 3 11 /16 6 3 /16 6 1 /2 12 7 /8 8 SWE311CC
KH-3164-2A F 3 15 /16 6 1 /2 7 1 /8 14 8 11 /32 SWE315CC
Recommended shaft tolerances: 13 /16” - 2" = nominal to – .0005"
2 1 /16" - 4", nominal to – .0010"